Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 2
Bert22306
User Rank
CEO
Re: PoE seems DOA - how does it scale to kW?
Bert22306   1/22/2014 5:13:42 PM
NO RATINGS
The original purpose of PoE was to allow VoIP phone instruments to get all the power they need from the Ethernet Cat-5e cable. Rather than having to connect a separate power cable. So this is just an update, to provide more power over the Ethernet cable.

The initial iteration was really simple. It used spare conductors in the 4 twisted pair Cat-5e to carry power. This is when Ethernet only needed two of the pairs. But then starting with 1000BASE-T, where all 4 pairs are needed for data, they had to get a little more clever. So basically power becomes the DC component on those twisted pairs.

Some Guy
User Rank
CEO
Re: PoE seems DOA - how does it scale to kW?
Some Guy   1/22/2014 5:13:08 PM
NO RATINGS
So then the main utility is when you are running a point to point connection to a single sensor / device directly connected to a hub that takes < 25W. OK that works.

So all the talk about powering your PC, or a workstation, or a whole building is just not practical, right? You aren't going to tap into a Cat 5/6 cable run and pull power at every drop. Got it.

Bert22306
User Rank
CEO
Re: PoE seems DOA - how does it scale to kW?
Bert22306   1/22/2014 5:07:12 PM
NO RATINGS
No magic here, Some Guy. PoE is something that only applies from one layer 2 switch port to the host attached at the other end of the cable. It's not like you're running power between switches and routers, over the network.

So, the only concern here would be how much aggregate power a single edge Ethernet switch can deliver, to its attached hosts. That's all.

If you have a building full of equipment, presumably you have more than just one edge Ethernet switch connecting to these end systems.

Some Guy
User Rank
CEO
Re: PoE seems DOA - how does it scale to kW?
Some Guy   1/22/2014 2:03:54 PM
NO RATINGS
From the energy research that I've done, the nominal you need at a minimally configured "guest" workstation is 106W for a monitor, phone (PBX-connected), cell phone charger and laptop charger. (163 if you want lights included.) You can get 100W from a USB 3.0 cable and 15-25W from PoE.

If I have to power the Ethernet hub at that workstation from AC mains to get PoE to all those devices, where does PoE help? If I have to power EVERY cubicle with AC mains to run a hub, how does that scale? That's not enough to power a single hub by USB 3.0. And if I'm going to use USB 3.0 why wouldn't I just use it for everything instead of PoE?

chanj0
User Rank
Manager
In Vehicle Application
chanj0   1/22/2014 1:44:55 PM
NO RATINGS
I can certainly see the benefit of having 1 cable running between host (Internet Gateway) and a device (e.g. an Infotainment device). However, given the space of a vehicle, I am not sure the finanical and production benefit. Another question needs to address is the energy loss. It is too soon to say there is any benefit of improving the power rating but it is definitely worth following.

asic_pal
User Rank
Rookie
Re: PoE seems DOA - how does it scale to kW?
asic_pal   1/22/2014 1:44:18 PM
NO RATINGS
I think PoE will be a point to point connection from the Hub to Endpoint. Hub will distribute power over Ethernet Cable to the Endpoints and the Hub may be powered by the PGE Power Port. If the Endpoints ar not power hungry, I believe Hub can also be powered by Ethernet Cable like USB.

It's my assumptions, I need to read the spec though :)

 

Kinnar
User Rank
CEO
Very Late Start
Kinnar   1/22/2014 1:18:28 PM
NO RATINGS
It is a very late initiative for promoting PoE, security cameras and authentication devices in the offices, industries and domestic environment are very much cluttered with network and power connections, at-least use of PoE will eliminate the power adapters and in turn the power supplies wiring. PoE is noting new but it is not promoted up-to extent it was required.

Some Guy
User Rank
CEO
PoE seems DOA - how does it scale to kW?
Some Guy   1/22/2014 1:18:03 PM
NO RATINGS
The thing I could never figure out about Power of Ethernet is how does it scale beyond 1 device. Over a 26 AWG wire in Cat6 cable I can power a device at 50W, but how do I power a whole building worth of devices to scale it to the killoWatts that an office building consumes? If I'm running 120 or 208 out to a bunch of distributed power supplies at every cubical or in parallel with every Ethernet cable ... I just don't see how it pencil's out.

Can someone help us with how you get around the conclusion that PoE may be great for 1 device, but brain-dead for a whole building's worth?

<<   <   Page 2 / 2


Flash Poll
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Rishabh N. Mahajani, High School Senior and Future Engineer

Future Engineers: Don’t 'Trip Up' on Your College Road Trip
Rishabh N. Mahajani, High School Senior and Future Engineer
1 Comment
A future engineer shares his impressions of a recent tour of top schools and offers advice on making the most of the time-honored tradition of the college road trip.

Max Maxfield

Juggling a Cornucopia of Projects
Max Maxfield
6 comments
I feel like I'm juggling a lot of hobby projects at the moment. The problem is that I can't juggle. Actually, that's not strictly true -- I can juggle ten fine china dinner plates, but ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
34 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Karen Field

July Cartoon Caption Contest: Let's Talk Some Trash
Karen Field
128 comments
Steve Jobs allegedly got his start by dumpster diving with the Computer Club at Homestead High in the early 1970s.

latest comment mhrackin Where's the "empty bin" link?
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)