Breaking News
Comments
You must login to participate in this chat. Please login.

can you explain slide 13 again.

Author

quite similar to what Eric teaches.

Author

Thank you Alfed and Martin.

Author

sorry, my typo:  replace "non-resonant" with non-50 ohms"".

 

Author

Thanks Al, I'am begining to understand.

Author

Hello again,

So if I measure the null-to-null spacing in the S11 plot from a non-resonant transmission line and then calculate the delay using your formula from yesterday:  delta f in GHz) = 1/(2*Td) is Td also the group delay?

Author

ukdave, thanks. That's often done on wafers as well, for failure analysis.

Good Afternoon, 9AM in the Morning here

Author

Joe, here's the lonk to yesterday's slides

http://downloads.deusm.com/eetimes/EETU/VNA-Manifesto-Jan-22.pptx

The Cal Structures are on the same board PANEL but not part of your finished board.

Author

Joe I'll get the link for you.

Travel glitches kept me form the class yesterday. Is the slide show and audio archived?

Author

No. I wouldn't go this year.

Author

On EMI/SI/PI panel and will be in the Simbeor Booth

 

Author

Anyone going to DesignCon next week?

Remember to post questions here

"I use airlines every week," said Al Neves, the self-proclaimed SI (signal integrity) Practitioner, at DesignCon 2013. He's also the Chief Technologist with Wild River ...

Note freq is in 10's of GHz

Author

What would the group delay average be?

so boards usually cal structures on them? What if there is no real estate?

Would you please define group delay?

Author

Remember to post questions here.

I'm going to need a refresher on Eigenvalues!

no audio, this webcast sucks!

Author

Good evening from Valladolid, Spain in the West Europe

 

Author

which slide is he on?

 

Author

hi frm MN/St. Paul

 

Author

 

Mishawaka is half way between Chicago and Detroit.

If you aim at Notre Dame you will miss Mishawaka by two miles.

 

 

hello from Mishawaka

 

Greetings from Scottsdale, AZ

Author

Colleen, what will yu do when Winter comes?

Good Morning Only 7 degrees this morning in Boston!

 

Author

Everyone, remember to downlaod your sildes from Today's Slide Deck

Hello Rodney. It's time for me get this set up. Day 4.

G Morning All

Rock n Roll!

Author


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...