Embedded Systems Conference
Breaking News
Comments
Oldest First | Newest First | Threaded View
Bert22306
User Rank
Author
Oh good! An opportunity to vent about 4 cylinder engines.
Bert22306   2/4/2014 4:58:13 PM
NO RATINGS
Automakers, all of them, need to appreciate that the more fuel and air they cram into a four cylinder engine, to get the power and torque numbers of a larger displacement 6 or 8 cylinder engine, the more the effect will be the same as a large displacement 4-banger. Even with balance shafts, that translates to a buzzy and unrefined four-banger. I've tried any number of brands, which received any number of accolades in magazine articles. This remains the case.

Please, automakers, at least as an option, please develop some small displacement, turbocharged or supercharged (if need be), 60 degree V-6s. Say, how about some sweet 2 liter V-6s? (And I say V-6 only because straight sixes are heavier and not easily applied to transverse-mounting for front wheel drive. Otherwise, the straight six is hard to beat for refinement.) As far as I'm concerned, any naturally aspirated four that displaces more than 1.5 or 1.6 liters will end up being buzzy. Two liters are simply too many, for a 4-cylinder. Let alone a turbo or supercharged four.

Yes, perhaps on the dyno, the 6-cylinder won't quite get the same fuel economy as a four with equivalent power. Perhaps. But I would ge glad to pay the extra fee for the 6-cylinder anyway.

Lancia had some wonderful small-displacement V-6s way back in the early 1960s. Surely, we can resurrect that formula? Any 300-HP four-banger will feel rough and rude, no matter the hype.

Etmax
User Rank
Author
Re: Oh good! An opportunity to vent about 4 cylinder engines.
Etmax   2/5/2014 8:04:42 PM
NO RATINGS
Absolutely, a 4 cylinder has less friction points than a 6Cyl or 8cyl and a 2.3l has much less weight than a 5l or more all which contribute to economy improvements, but ultimately 300hp is going to the wheels and has to come from somewhere.

Maybe they gain 3% from having a 4cyl and another 5% from the weight savings but the thing will still be a guzzler when the petal is to the metal.

But as far as Mustangs goes, it won't be a muscle car with a 100hp motor of any type.

We just have to accept that a Mustang owner has more money than environmental responsibility.

Just on the by n by a friend of mine let me drive his 400hp Porsche for a bit, and there was nothing buzzy about it. Sure it was a flat 6 but it only roared under powerful acceleration.

Bert22306
User Rank
Author
Re: Oh good! An opportunity to vent about 4 cylinder engines.
Bert22306   2/5/2014 8:21:34 PM
NO RATINGS
Just on the by n by a friend of mine let me drive his 400hp Porsche for a bit, and there was nothing buzzy about it. Sure it was a flat 6 but it only roared under powerful acceleration.

Obviously, It was a flat 6, not a four.

I once owned a 1.4 liter DOHC Fiat 124 Sport. The small engine displacement made that a smooth engine too, although it did have the odd hiccups you get from 4 cylinder engines at very low revs. My point is, fours are still fours, no matter whether you show on paper that the power output is high. They are not refined-sounding or refined-feeling. The extra drag of two more cylinders I'll gladly pay for, if given an option.

As to engine weight comparisons, here, surprise yourself:

http://www.gomog.com/allmorgan/engineweights2.html

Modern V-6s weigh about the same as a four of similar displacement. So, make some small displacement V-6s!

Etmax
User Rank
Author
Re: Oh good! An opportunity to vent about 4 cylinder engines.
Etmax   2/5/2014 10:10:58 PM
NO RATINGS
Bert, I was actually comparing the weight difference between a 2.3l 4cyl as used in the Mustang and a 4-5l V6/V8 as used in your typical muscle car of similar power, for the puposes of highlighting where the meagre saving would come from. Sorry for not having been clearer. I agree for same displacement there shouldn't be much weight difference.

I too prefer a 6Cyl to a 4Cyl, but the running gear friction/losses in a 4 is lower resulting in better efficiency.

Of course the fewer cylinders the lumpier.

I referenced the Porsche experience because you made mention of all powerful engines being.. can't remember the term but perhaps I misunderstood as we seem to be on the same page.



Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...