Breaking News
Newest First | Oldest First | Threaded View
User Rank
Did the experiment again - This time with data
chrlilje   2/8/2014 3:17:47 PM
Very interesting comments to this topic. 

- I didn't take any measurements by the first experiment, since it was just a "does it work at all" test. 

But, today I redid the test, this time recording the wifi-strength using the method in the Electric Imp ide doing just that: imp.rssi() ( )

Here is a graph of the data - There is roughly a drop in signal strength of 10 dBm when the imp is dipped in oil.

To counter any errors from changing the position of the imp in the room influencing the wifi-strength, i had the imp hanging in a fixed position, and lifted the cup of oil up around it. 

Another possible error/uncertainty in this is, that the antenna of the imp is hidden in the plastic container. Most likely the antenna does not get in direct contact with oil. There is most likely at least 1 mm of air/plastic between the antenna and the oil. 

Kind regards

Christian Liljedahl

User Rank
Re: Sort of related...
MPOP   2/8/2014 1:43:45 AM
And also, cooking oil is known to have a relative low resistivity (it has got some ions an water in it) - which is certainly increasing electric and electromagnetic losses. This is a known problem - only silicon and transformer oil has good dielectric properties, having very high resistivity, temperature resistance and high breaking voltage.

User Rank
Re: Sort of related...
MPOP   2/8/2014 1:35:15 AM
Yes, it seems correct that the epsilon of oil is changing everything about the line impedances, etc; Then, maybe the best solution is to run a simulation of redesigning such a circuit optimized for the new epsilon and see the differences. As a reduction, only the impedance of the transmission/ reception wifi may be considered but I wouldn't be to surprised to find out that all the on- board line transmissions are affected. As a first guess, increasing epsilon would cause decreasing the size of the board - that's interesting.

User Rank
Re: Interesting question....any expert opinions out there?
bk11   2/7/2014 3:57:58 PM
It's an easy experiment.  Measure signal strength with the device in air.  Then put the device in a sealable plastic bag, and measure signal strength again.  Then submerge the bag in oil (thus preserving the air interface for the antenna) and measure.  Finally, take the device out of the bag and submerge it.

I suspect that only the un-bagged, submerged case would show a drop in signal strength, because I think the antenna mismatch theory is spot on.  Waves passing through a dielectric interface will refract, but not necessarily attenuate, but an impedance mismatch would cause a reflection.

User Rank
Re: Interesting question....any expert opinions out there?
ltaibbi   2/7/2014 2:44:53 PM
If the previous "proofs" bear fruit then might the oil-to-glass interface contribute additional impedance mismatch as well? Also, might crystal type wine glasses have high lead content?

User Rank
Interesting question....any expert opinions out there?
ChrisJ555   2/7/2014 2:32:49 PM
I'm no expert, but this is an interesting question.  Seems like one should be able to find the attentuation values for oil (BTW, what kind of oil is it?) somewhere, then that would answer half of the question.

Also - correct me if I'm wrong, but wouldn't the "air bubble" idea just be moving the mismatched-impedance boundary out farther, i.e. it would still have its effect (whatever that may be) at distances beyond it?

User Rank
Sort of related...
tom-ii   2/7/2014 10:30:52 AM
So, I once had a requirement to prove that a system installed subsea would meet EMI requirements.  Including radiated.  (seriously).  Here is my write-up for that - I would assume that while the Reddit guy is partially correct (interface impedance), there is also something to be said for the energy absorption of the oil (although I agree - that is probably pretty low in this particular instance)...


Not a real proof, I'll admit, but...


Shielding Effectiveness of Sea Water

According to [1] and [3], the shielding effectiveness of a shielding mechanism is defined as:



P1 = Incident Electromagnetic Power

P2 = Transmitted power with shielding in place

R = Reflection loss

A = Absorption loss

C = correction term for re-reflection within the metal surfaces

Furthermore, according to [1], the correction term (C) is usually of small magnitude and is ignored when the absorption loss is greater than about 10dB.

According to [1], the reflection loss for plane waves is as follows:


And absorption loss is:





µ = Permeability of the material

g = Conductivity of the material

µ0 = Permeability of free space (4πx10-7 h/m)

gcu = Conductivity of Copper (5.8x107 S/m)

µr = Permeability relative to Copper

gr = Conductivity relative to Copper

f = Frequency in Hz

d = Thickness of material in meters

According to [2], the properties of sea water are as follows:


Combining these values, we find that one meter of sea water has a shielding effectiveness of approximately 125dB at 1Hz, dipping to 101dB at approximately 50kHz, and then increases log-linearly to over 500dB at 1GHz. This curve is shown in figure 1, below. Changing the distance between the noise source and the receiver effects only the slope of the absorption curve – at 10m distance, the knee of the curve moves to 0.1MHz, and this trend continues as depth increases.

As most EMI screen rooms afford 100 dB shielding, and do an effective job at blocking outside radiation, it seems appropriate to consider the system to be contained within a very good Faraday cage.



[1] MIL-HDBK-1195, Military Handbook, Radio Frequency Shielded Enclosures, September, 1988

[2] Omer Tolga Inan, Naval Technological Innovations of World War II, March, 2004


What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by: Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
With design sizes expected to increase by 5X through 2020, ...
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...