Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 3 / 3
HankWalker
User Rank
Manager
193i + E-beam?
HankWalker   2/26/2014 12:59:55 PM
NO RATINGS
What about 193i (or nanoimprint as used in disk drives) to form parallel lines and e-beam to cut them and form vias? TSMC has a Mapper prototype system. David Lam is targeting Multibeam for this purpose, rather than rastering a mask, since it has much relaxed overlay/resolution/writing speed requirements compared to rastering the whole wafer.

157 died since it was a lot of investment for relatively little gain in process capability. EUV may start to be in that position, unless it can demonstrate significant capability improvement or cost reduction at the time it would be inserted.

 

rick merritt
User Rank
Author
7nm without EUV
rick merritt   2/26/2014 10:49:18 AM
NO RATINGS
That was the title of a panel at the SPIE Litho conference in San Jose last nite: "7nm without EUV"

If anyone went, I'd love to hear a digest of what was said. In any case, what do you think are the viable options?

zewde yeraswork
User Rank
Blogger
Re: Do you still believe in EUV?
zewde yeraswork   2/26/2014 9:32:15 AM
NO RATINGS
EUV is an interesting avenue for making chips faster and smaller and dealing with the upcoming end to Moore's Law, but it's far from a sure thing that's true.

yangcoloy
User Rank
Rookie
Re: Do you still believe in EUV?
yangcoloy   2/26/2014 2:30:37 AM
NO RATINGS
EUV feels like the old 157nm. However, as there is not an innovation like water immersion yet.

resistion
User Rank
CEO
Re: Do you still believe in EUV?
resistion   2/25/2014 7:48:40 PM
NO RATINGS
At SPIE 2008, TSMC published a paper which talked about shot noise for the different lithography technologies and its impact on CD uniformity. EUV already had trouble in this area at 30 nm, so for the 20 nm size applications, it would have a prohibitive impact on minimum dose requirements, as that would drive up the source power requirement many times beyond the currently already difficult-to-reach target level.

The paper title is "Influence of Shot Noise on CDU with DUV, EUV, and E-Beam"

JimMcGregor
User Rank
Blogger
Re: Do you still believe in EUV?
JimMcGregor   2/25/2014 7:07:20 PM
NO RATINGS
Rick, I would agree. The process is gaining in complexity and while EUV still holds potential, the feasibility of the technology remains in question.

resistion
User Rank
CEO
Re: Do you still believe in EUV?
resistion   2/25/2014 4:10:18 PM
NO RATINGS
Just looking at the data it's not revived EUV hope but continuing reality.

rick merritt
User Rank
Author
Do you still believe in EUV?
rick merritt   2/25/2014 1:51:04 PM
NO RATINGS
Looks like a case of Herculean efforts but modest progress to me.

<<   <   Page 3 / 3


EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Aging Brass: Cow Poop vs. Horse Doo-Doo
Max Maxfield
40 comments
As you may recall, one of the things I want to do with the brass panels I'm using in my Inamorata Prognostication Engine is to make them look really old. Since everything is being mounted ...

EDN Staff

11 Summer Vacation Spots for Engineers
EDN Staff
11 comments
This collection of places from technology history, museums, and modern marvels is a roadmap for an engineering adventure that will take you around the world. Here are just a few spots ...

Glen Chenier

Engineers Solve Analog/Digital Problem, Invent Creative Expletives
Glen Chenier
11 comments
- An analog engineer and a digital engineer join forces, use their respective skills, and pull a few bunnies out of a hat to troubleshoot a system with which they are completely ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
45 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Flash Poll
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)