Embedded Systems Conference
Breaking News
Newest First | Oldest First | Threaded View
<<   <   Page 4 / 4
User Rank
PCB Shorts
Etmax   2/26/2014 7:51:32 PM
Well my fist thought would be why the CAD SW designer had a separate switch for copper pours, clearance is clearance, and why you would not want to do a clearance check I don't know. I use OrCAD and Altium and I'm not sure about Altium, but OrCAD had a DRC button that checks everything. You can set the rules for pours differently (as you should) but DRC for clearances is DRC for all clearances. Sounds like designed by monkeys.

My second thought is why your PCB maker doesn't do a DRC check against their capabilities before they start the job, it seems totally silly unless they don't warrant their product and so don't care.

My final thought is why they didn't do a bare board test? My supplier does BBT on all boards at no extra cost, I might be loading $1000 worth of parts onto what is only a $5. bare board, why would I want to use an untested part? Would you build the whole board from untested parts from the manufacturer? I doubt they would sell untested parts because their reputation is important.

I don't know, maybe I'm an OCD sufferer, but for me the cost of repairing production boards would far outweigh the cost of a supplier that does DRC & BBT.

User Rank
OSH Park
DeeCee430   2/26/2014 7:43:31 PM
Although I haven't yet used OSH Park to make any boards for me, in the past few weeks I have twice e-mailed them with various questions, and both times the response by Dan Sheadel:
  1. answered all my questions, not just some of them
  2. completely answered my questions, not just partially
  3. the quality of his answers showed that he had actually read and understood my questions
  4. the answers came the same day

In my experience, this is very rare.

User Rank
checking the Gerber files
DeeCee430   2/26/2014 6:57:18 PM
Had you checked the Gerber files with a Gerber viewer before sending the board to be manufactured?

On the other hand, a few years ago I used the Batch PCB service from SparkFun to make a board that had a filled outline (copper pour). I specified the RS-274X file format, with G36/G37 enabled. My Gerber viewer (ViewMate from Pentalogix) and the Batch PCB design checker both showed the copper pour was OK. But the board that came back only had the thin line around the outside edge of the copper pour. Luckily I had also used thick traces (this was the important GND net) to connect the pins, so the circuit worked. Maybe the board shop thought that the copper pour and the traces weren't both needed, so deleted the pour? Or they just accidentally deleted the copper pour? Who knows. When I sent an e-mail to Batch PCB, I never got a response. By the way, another copper pour on the other side of the same board was OK.

I am currently working on a board design that I plan to send to OSH Park. When I used ViewMate to view the Easy-PC v17 generated Gerber files, I was surprised (but shouldn't have been) to find that they did not totally match my design.

I had used 0 width lines to specify various filled outlines (yes, the Gerber specification explicitly says they are acceptable for creating G36 regions), but Easy-PC had changed them to 1 mil lines, without warning me. This caused all areas to grow by 1/2 mil on each side, which caused some clearances to be less than required.

Also, I had used some rounded rectangle pads. Easy-PC didn't use arcs for the corners, but instead generated 2 or 3 line segments to approximate the arc, which looks ugly. The Gerber specification has an example of how to write a macro to generate rounded rectangle pads -- it's actually easier than using line segments.

Not using enough resolution for the Gerber coordinates can also make the manufactured board vary from the design due to rounding errors. Ucamco (who produce the official Gerber file specification) actually suggest using 6 decimal places for inches, and 5 for millimetres.


<<   <   Page 4 / 4

As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...