Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 4 / 5   >   >>
optoeng
User Rank
Rookie
One man's minimum...
optoeng   3/5/2014 5:43:44 PM
NO RATINGS
Absolutely MUST haves:

low power stereo microscope

non-magnetic tweezers

rotary crafting tool (Dremel)

scalpel or very sharp craft knife

 

betajet
User Rank
CEO
Re: Forceps and Panavice
betajet   3/5/2014 12:55:31 PM
NO RATINGS
elizabeth wrote: I've found that having a small or medium forceps around is really helpful for holding wire and resistor leads that are about to be soldered to something.

You can often fake this by looping a rubber band around the handles of your needle-nose pliers.

Max The Magnificent
User Rank
Blogger
Re: Forceps and Panavice
Max The Magnificent   3/5/2014 12:18:51 PM
NO RATINGS
@Elizabeth: The head mounted magnifier and LED light combination looks really nice. I might just have to get one of those...

On the one hand it's relatively cheap-and-cheerful -- on the other hand it comes with a little case containing 5 dual-lens arrangements that take you from 1.5X to 3.5X -- and for $5 (and I think that might have included the postage) you simply cannot go wrong.


Do you want me to try to find the actual product number on Amazon?

elizabethsimon
User Rank
CEO
Forceps and Panavice
elizabethsimon   3/5/2014 11:15:33 AM
NO RATINGS
I've found that having a small or medium forceps around is really helpful for holding wirsa and resistor leads that are about to be soldered tosomething. The needle nose pliers work but I often lose the grip on the wire while manovering it into position. The forceps can be latched shut which really helps sometimes.

I'm also really fond of my Panavice for holding boards and connectors in position to be soldered.

The head mounted magnifier and LED light combination looks really nice. I might just have to get one of those...

Steam Kid
User Rank
Rookie
Re: De-soldering tool
Steam Kid   3/5/2014 4:33:15 AM
NO RATINGS
Substitute Hot-Air gun for Blower, great for surface mount device removal and usable for Thro' Hole devices but watch out for hooked legs that can pull out plated holes. Tool wise I rate multimeters and oscillatorscopes as my must have tools.

betajet
User Rank
CEO
Re: Why a Wrap?
betajet   3/4/2014 6:03:52 PM
NO RATINGS
Some kittens (and cats) like to chew on wires.  They're not as destructive as rabbits, but you might want to invest in cable organizers/protectors now.

TonyTib
User Rank
CEO
How much to spend depends on use
TonyTib   3/4/2014 5:44:13 PM
NO RATINGS
For tools, how much to spend depends on how much you expect to use it. 

For one time use, borrow it or buy Harbor Freight.

For stuff you use all the time, get good quality (but not the most expensive, e.g. Wiha screwdrivers, Bondhus hex wrenches, but not $70 Swedish diag cutters, Snap On, etc) -- oh, and it's good to have some cheap stuff that you don't care if it gets broken (e.g. Harbor Freight screwdrivers for prying and poking -- and to be fair to HF, I should note they do have some good stuff, too).


For soldering, I highly recommend a controllable temperature soldering iron, since lead and lead free solders work best at different temperatures.  For finer pitch work, I've seen recommendations for hot air rework, but don't have one yet.

Max The Magnificent
User Rank
Blogger
Re: De-soldering tool
Max The Magnificent   3/4/2014 5:35:53 PM
NO RATINGS
@GarySTX: To minimize the chance of damaging the board you need something to help remove the solder.

I've used both the braid and the solder sucker -- each works best in different cases. Recently I read about someone who used a "blower" rather than a sucker -- but I don't remember much about it -- do you know anything about this technique?

Max The Magnificent
User Rank
Blogger
Re: Why a Wrap?
Max The Magnificent   3/4/2014 5:33:16 PM
NO RATINGS
@Betajet: Solderless breadboards are also great for quick projects, but don't expect them to stay intact if you have cats :-)


My wife just got a new cat (her last one passed away age 17 a couple of months ago). This new one is a very energetic kitten. I heard a disturbing sound yesterday evening -- when I looked up it was strolling across our breakfast table, upon which was my current Arduinoi project with a rats nest (no pun intended) of wires. I don;t think I need to describe the end result (sad face)

 

GarySXT
User Rank
Freelancer
De-soldering tool
GarySXT   3/4/2014 5:28:31 PM
If you solder parts on a circuit board, sooner or later you will have remove one because you installed the wrong part, need to change the value to get the circuit to work, or you make a mistake and let the magic smoke out.  To minimize the chance of damaging the board you need something to help remove the solder.

I prefer the larger spring loaded solder suckers. I never found a small one that works well. Solder braid is another option, but you have to buy more as you finish a roll. It also does not work as well at getting the solder out of plated through holes.

<<   <   Page 4 / 5   >   >>


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
<b><a href=Betajet">

The Circle – The Future's Imperfect in the Present Tense
Betajet
5 comments
The Circle, a satirical, dystopian novel published in 2013 by San Francisco-based writer Dave Eggers, is about a large, very powerful technology company that combines aspects of Google, ...

Max Maxfield

Recommended Reads From the Engineer's Bookshelf
Max Maxfield
25 comments
I'm not sure if I read more than most folks or not, but I do I know that I spend quite a lot of time reading. I hate to be idle, so I always have a book or two somewhere about my person -- ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...