Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 5   >   >>
mhrackin
User Rank
Author
Re: rework tools: My old Xacto from desk
mhrackin   3/11/2014 12:09:01 PM
NO RATINGS
I still don't understand why I can't put a photo in a post.  I've seen them in other (old) posts, but the new tool it seems only lets you insert a a link to a photo already on the Web!

mhrackin
User Rank
Author
Re: rework tools: My old Xacto from desk
mhrackin   3/10/2014 5:07:02 PM
NO RATINGS
Nor I.  I have several; this one is at least 30 years old.  Unfortunately I can't insert the image! 

 

 

 

Max The Magnificent
User Rank
Author
Re: rework tools
Max The Magnificent   3/10/2014 1:46:27 PM
NO RATINGS
@MWagner_MA: Max don't forget the "X-Acto" knife

I wouldn't be without one :-)

Max The Magnificent
User Rank
Author
Re: Cheaper Alternatives
Max The Magnificent   3/10/2014 1:43:13 PM
NO RATINGS
@betajet: I've been using those kinds of terminals for decades and I always thought they required solder!

I agree -- I've always soldered mine.

Max The Magnificent
User Rank
Author
Re: DIY Tools
Max The Magnificent   3/10/2014 1:41:40 PM
NO RATINGS
@_hm: One important missing tool is wrist strap and anti-staitc mat to prevent damage to ESD senstive electronics.

This is a very good point -- I've been caught out myself by ESD more than once.

betajet
User Rank
Author
Re: Pretty good list
betajet   3/10/2014 1:25:53 PM
NO RATINGS
@LiketoBike: That screwdriver set should be one of the sets with umpteen billion bits...because you WILL need esoteric bits sooner or later.

The problem is that when the time comes you'll need different esoteric bits because the best-known manufacturer of hard-to-disassemble technology -- let's call it "Brand A" -- makes it a point that each new product (or so it seems) uses a new type of fastener :-)

MWagner_MA
User Rank
Author
rework tools
MWagner_MA   3/10/2014 12:28:29 PM
NO RATINGS
Max don't forget the "X-Acto" knife (with the #11 blade) for trace cuts and small roll of kapton tape (its expensive so go small!).  The tape allows you to break a connection to a SOIC pin without mangling it and still allow a small #30 wire to be soldered to it.  This is of course only necessary until your board is perfect ;-)

Max The Magnificent
User Rank
Author
Re: DIY Tools
Max The Magnificent   3/10/2014 11:09:56 AM
NO RATINGS
@David: ...a drill - also an essential tool that no-one else seems to have mentioned.

Good point -- I have a little Dremel I keep to hand (as we all know, it's not the size of your Dremel, it's what you do with it that counts)

mhrackin
User Rank
Author
Re: Cheaper Alternatives
mhrackin   3/10/2014 10:57:23 AM
NO RATINGS
I second the motion!  And, having recently entered my eightth decade (seventh in elctronics design and construction), I am STILL doing it that way.  I even did that until recently (when our lab tech bought an "approved" crimper for them) with FAKRA RF connector center pins and sockets!  It does take a bit longer, as I have hardly any "feel" left in my fingertips, but it does work.  I've raised the ability to solder the connections with the absolute minimum of residue on the outside to a new level,  so contacts will still fit in the housings and lock in place.  Having not only my own substantial collection of hand (and power) tools, i also inherited my father's many years ago, and so have at least duplicates of nearly everything!

antedeluvian
User Rank
Author
Re: Pretty good list
antedeluvian   3/10/2014 10:26:29 AM
NO RATINGS
LikeToBike and Max

I have a crimper -- I think it does act as a wire stripper and cutter also, but I use it onlt for crimping

Mine is also a bolt cutter for up to 8-32 IIRC. Has proved to be very convenient at times.

 

Page 1 / 5   >   >>


Radio
NEXT UPCOMING BROADCAST
Drones are, in essence, flying autonomous vehicles. Pros & cons surrounding drones today might well foreshadow the debate over the development of self-driving cars. In the context of a strongly regulated aviation industry, "self-flying" drones pose a fresh challenge. How safe is it to fly drones in different environments? Should drones be required for visual line of sight, as are piloted airplanes? Is the technology advancing faster than we can answer the questions it poses? Panelists: Chad Sweet, Director of Engineering, Qualcomm; Yannick Levy, VP Corporate Business Development, Parrot; Jim Williams, ex-FAA drone chief; Michael Drobac, Exec. Director, Small UAV Coalition; Moderator: Junko Yoshida, Chief Int'l Correspondent, EE Times
July 16, 1pm EDT Thursday
IoT Network Shoot Out
Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...