Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 5   >   >>
Max The Magnificent
User Rank
Blogger
Re: How to determine a true DIY geek:
Max The Magnificent   3/10/2014 10:20:49 AM
NO RATINGS
@pseudoid: I have not seen anyone recommend a DMM.

I mentioned a DMM in the main slideshow -- I didn't recommend a particvular make -- I just said it's one of the essential pieces of equipment.

Max The Magnificent
User Rank
Blogger
Re: Pretty good list
Max The Magnificent   3/10/2014 10:19:02 AM
NO RATINGS
@LiketoBike: I like a cigarette lighter for quick jobs with heat-shrink tubing, or lighting my torch.  For that matter, electric tape, epoxy, heat-shrink tubing and nylon tie-wraps are very useful for bonding things.

I have a handy-dandy llittle hot air blower for heat-shrink tubing -- I do like small nylon tie-wraps for keeping things tidy -- and I'm also a big fan of the hot glue gun LOL

Max The Magnificent
User Rank
Blogger
Re: Pretty good list
Max The Magnificent   3/10/2014 10:17:03 AM
NO RATINGS
@LiketoBike: Concerning the wire stripper:  many of these also can crimp solderless terminals.  Make sure your wire stripper is so equipped, and solderless spade lug terminals, butt connectors, and some multipin connector terminals become usable.

I have a crimper -- I think it does act as a wire stripper and cutter also, but I use it onlt for crimping -- it's funny how you get to have a favorite tool for each task.

Max The Magnificent
User Rank
Blogger
Re: Pretty good list
Max The Magnificent   3/10/2014 10:15:06 AM
NO RATINGS
@LiketoBike: That screwdriver set should be one of the sets with umpteen billion bits...because you WILL need esoteric bits sooner or later.  I include sockets/nutdrivers here.

I agree -- I have a nice set that includes screwdrivers, and sockets/nutdrivers.

pseudoid
User Rank
Manager
How to determine a true DIY geek:
pseudoid   3/8/2014 4:28:07 PM
NO RATINGS
The sole question to ask is "Do the tools make the man or does the man make the tools?"  >> The ONLY acceptable answer is "Yes".

The problem with buying 'cheap' and/or 'all in one' tools is the fact that they end up cluttering another needed tool which is a toolbox.

I have not seen anyone recommend a DMM and of course you can get the free one from Harbor Freight Tools but you gets what you pays for!  One can always use old wallwarts to serve the power supply needs but there is no substitute for a DMM.

cookiejar
User Rank
CEO
Re: yet another tool
cookiejar   3/8/2014 3:32:30 PM
NO RATINGS
I have to agree with Tom.Grey on the value of a crimping tool. 
I've bought about a dozen wire stripping tools in my day, none of which worked better than my pair of diagonal cutters.   I know using the cutters is playing chicken, as it's easy to nick or even sever the wire, but for some reason I have more problems with sole purpose wire strippers either not removing the insulation in one piece or nicking the wire.
My favorite tools is the Super Champ crimping tool from Amp.  Besides crimping terminals, it's wire stripper functions well on 22 to 10 A.W.G.,  better than any of my other wire strippers and it has a bolt cutter for cleaning cutting machine screws number 4, 6, 8 and 10.  My specimen is over 40 years old and has put to shame all other imitators I've gotten to put in my garage tool kit through the years.  This is a quality tool.
I still use my red plastic nut starters that used to come with every Heathkit.
My indespensable tool for surface mount components is my Baush and Lomb stereo zoom microscope with a decent fiber optic illumination setup.  It actually makes working with surface mount a pleasure, considering my aging eyes.  I picked up my setup at a surplus place for under $500.  Many are the hours I've spent using it to examine insects and other life forms, printed material and just about anything I'm curious about.  The rest of the family really enjoy it too. 


Tom.Grey
User Rank
Rookie
yet another tool
Tom.Grey   3/8/2014 1:40:44 PM
NO RATINGS
I have found a combination "crimper stripper cutter" tool (use those terms in your favorite search engine) to be very useful.  Typically less than $25 US.  Crimps those solderless connectors, strips wire of various gauges, typicaly has a wire cutter, and also will cut small machine screws that invariably are just a little too long for your project.  A smaller dedicated wire stripper is also handy as the above tool is a little bulky.

Crusty1
User Rank
CEO
Re: Cheaper Alternatives
Crusty1   3/8/2014 9:19:03 AM
NO RATINGS
@betajet; Yes up to now I have soldered and used small pliers, but eye sight is going, hands are getting unsteady. I am due for the scrap heap soon so need a tool that works better than my lumpy old fingers.

betajet
User Rank
CEO
Re: Cheaper Alternatives
betajet   3/8/2014 9:14:07 AM
NO RATINGS
Crusty asked: However what alternative do people use for crimping JST (JAPAN SOLDERLESS TERMINALS) - BXH-001T-P0.6 - CRIMP TERMINAL, XH, 28-22AWG?

Those are solderless?  Gee, I've been using those kinds of terminals for decades and I always thought they required solder!  Seriously, I first used them in Heathkits and they required that you wrap the flanges around the wire using needle-nose pliers and then solder.  I guess they figured that nobody would have a US$600 crimping tool and if they're building Heathkits they have the time to wrap the flanges and solder -- probably makes better contact too.

_hm
User Rank
CEO
Re: DIY Tools
_hm   3/8/2014 5:57:36 AM
NO RATINGS
@max: One important missing tool is wrist strap and anti-staitc mat to prevent damage to ESD senstive electronics.

Also image does show you follow advice of your father! All tools looks low cost and can break at anytime. You need to show good tools images which last very long.

<<   <   Page 2 / 5   >   >>


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Tired Old iPad 2 vs. Shiny New iPad Air 2
Max Maxfield
8 comments
I remember when the first iPad came out deep in the mists of time we used to call 2010. Actually, that's only four years ago, but it seems like a lifetime away -- I mean; can you remember ...

<b><a href=Betajet">

The Circle – The Future's Imperfect in the Present Tense
Betajet
5 comments
The Circle, a satirical, dystopian novel published in 2013 by San Francisco-based writer Dave Eggers, is about a large, very powerful technology company that combines aspects of Google, ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...