Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 2   >   >>
MeasurementBlues
User Rank
Author
Old test equipment and a future engineer
MeasurementBlues   4/1/2014 9:50:18 AM
NO RATINGS
See Vintage test equipment: Not just for old engineers where I give a firsthand look at a high-school student's collection of vintage test equipment.

MeasurementBlues
User Rank
Author
The beauty of old test equipment
MeasurementBlues   4/1/2014 9:47:52 AM
NO RATINGS
Dedicated knobs, no menus, easier to fix. No software. OK you don't get PC connectivity. Life is a tradeoff.

Caleb Kraft
User Rank
Author
Re: Senior citizen?
Caleb Kraft   3/30/2014 5:38:19 PM
NO RATINGS
I believe there is a Jr. Version that is not as fancy.

Susan Rambo
User Rank
Author
Senior citizen?
Susan Rambo   3/29/2014 2:51:46 PM
NO RATINGS
Caleb, why do they call it "senior"?

Rocket_G
User Rank
Author
Re: similar to Heathkit V7-A
Rocket_G   3/28/2014 9:12:39 PM
NO RATINGS
Cool! As a teenager I built a Heathkit IM-11 back in the 1960's, learned a lot about vacuum tube circuits from the build, and got lots of use out of it.  The RCA VoltOhmyst looked familiar to me as well.  Sometime in my undergrad years (B.S.E.E.) I gave it away to an aspiring young EE.

herbissimus
User Rank
Author
Re: Waxed paper parts
herbissimus   3/27/2014 7:22:44 PM
NO RATINGS
those of us, for most if not all measurements lived in a world of plus or minus ten percent. mirror not necessary. as to only $15.oo : minimum wage was less than 1 dollar. i couldn't afford a new one. today any autoparts store's got one for $10-$30 that can measure to 1% and has a pretty good repeatability and runs on batteries which vtvm's did not, usually.

Wnderer
User Rank
Author
Re: Waxed paper parts
Wnderer   3/27/2014 1:53:20 PM
NO RATINGS
More memories from high school.

I recall they used to make precision values of resistors by filing them. They may be using the wax to protect the ground sections after setting the value. I'm not sure about this, though.

cookiejar
User Rank
Author
similar to Heathkit V7-A
cookiejar   3/27/2014 12:15:37 PM
NO RATINGS
I still have my Heathkit V7-A VTVM which I built in 1957 working.  It's a close cousin to the RCA who had all the standard tube circuits in their tube manuals.  The Heathkit has a db scale and no separate scale for the 1.5V range.  In the 60s I replaced the 1.5V D cell for the ohms function with a power supply kit sold for that function and the zero and ohms pots with the vernier (planetary ball) pots availble from Heath which made setting zero and ohms far less touchy.

Those wax covered paper tubes are hiding the reistor values underneath them.  Who knows what purpose they serve. If you look at the schematic, there are very few caps in the circuit. 

I'm impressed that all my Heathkit tube equipment from the 50s and 60s still functions very well indeed. The only repair I've had to do is replace a resistor in the AG-9A audio generator which had too low a wattage rating causing value shift and 4% harmonic distortion.  After that fix the distortion went down to under 0.02%.

I still mourn the death of Heathkit, like a long lost friend.  They got me into electronics after all.

 

Caleb Kraft
User Rank
Author
Re: No Mirror?
Caleb Kraft   3/27/2014 11:05:46 AM
NO RATINGS
Oh I see! Thanks for the link.

Wnderer
User Rank
Author
Re: No Mirror?
Wnderer   3/27/2014 10:58:18 AM
NO RATINGS
Here's a link.

http://www.radio-electronics.com/info/t_and_m/analogue-multimeter-voa-vom/how-to-use-using-analog-meter.php

 

I was taught in high school to use these meters. You line up the needle with the one in the mirror to get an accurate reading.

Page 1 / 2   >   >>


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...