Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 5   >   >>
David Ashton
User Rank
Blogger
Re: Twisted WIre
David Ashton   4/26/2014 6:49:30 AM
NO RATINGS
@Pablo - wire from Cat5 / 6 network cable - the solid stuff, not the stranded patch cable - makes excellent jumpers for breadboards too.  At least 5 colours - 8 if you're lucky -  for easy wire identification....

David Ashton
User Rank
Blogger
Re: I want a finger wrench!
David Ashton   4/26/2014 6:44:06 AM
NO RATINGS
@GSKrasle - some fine tips there too.  Ref your last:

"It's useful to have a scrap of cardboard at the soldering-station to avoid damaging more delicate surfaces."

I had a Weller iron that had a square of yellow fibrous stuff for cleaning the tip.  You had to keep it wet.  It wore out in time and I found that a square of very similar looking material from a floor mop worked just as well.  I recently got some genuine Weller ones and honestly the floor mop stuff is just as good - and much cheaper!

antedeluvian
User Rank
Blogger
Re: Removing Labels
antedeluvian   4/25/2014 8:17:43 PM
NO RATINGS
Pablo

For removing labels a heat gun is even better than WD-40 and doesn't leave any residue or smear the print on the label. 

You are absolutely correct. I use a paint scraper together with the heat gun to make short work of the sticker. The problem is when the sticker is on a plastic housing. Excess heat can have disfiguring consequences.

PabloBrysono
User Rank
Rookie
Twisted WIre
PabloBrysono   4/25/2014 4:38:25 PM
NO RATINGS
When I need a twisted pair I just cut up a  spare or faulty network cable and parallel the wires if I need more current capability. 

PabloBrysono
User Rank
Rookie
Removing Labels
PabloBrysono   4/25/2014 4:32:47 PM
NO RATINGS
For removing labels a heat gun is even better than WD-40 and doesn't leave any residue or smear the print on the label. 

GSKrasle
User Rank
CEO
Re: Binder Clips
GSKrasle   4/25/2014 4:22:51 PM
NO RATINGS
I want to see other, more circuit-oriented ideas!

Here's one:

Sometimes, you need plain-old diodes, but at high-wattage (e.g. as part of a test load). High-W diodes are costly. But MOSFETs are not! Who needs a "Gate"?

In fact, let me go-on: make a load by attaching a chain of diodes with n*Vf>Vs to the node to be loaded (a resistor in the chain helps with controllability/metering). In series with this, use a bench adjustable supply. No current flows until you adjust the bench supply high-enough, and its I-limit is useful. Just put a diode around it so that it won't hurt the DUT if the DUT turns-off/folds-back.

GSKrasle
User Rank
CEO
Re: Binder Clips
GSKrasle   4/25/2014 3:48:09 PM
NO RATINGS
Binder-clips: very nice. I hate shredding the probe cords.
Why don't scopes have "cupholders" for the witch-hats?

I once had to deal with prototypes that were many times larger than the intended product PCBs. Unfortunately, the mfr had used the same very thin PCB material, and even with lots of standoffs as "feet," the boards would flex alarmingly. I screwed them to panels of insulating foam with wood-screws. Luckily, no significant componentry on the bottom).

We've all touched plastic with a soldering-iron before.... To clean-off the smell, use a brass/copper "scrubber" while it's hot.

Cut-out a piece of an aluminum soda-can. Fold/crease it. Cut it into a triangle. Taa-Daa! A disposable tweezers of any dimension you need. (Entomologists do this.)

X-acto blade dull? Break-off (eye-protection!) a bit of it to get to an un-worn part of the edge.

 

 

Wnderer
User Rank
CEO
Binder Clips
Wnderer   4/25/2014 3:09:16 PM
NO RATINGS
I put tiny binder clips on my oscilloscope probes.

http://en.wikipedia.org/wiki/Binder_clip

They are useful for holding a scope probe in place with a helping hand or hanging the unused ground clip without chewing up the cable with the alligator clips.

zeeglen
User Rank
Blogger
Re: I want a finger wrench!
zeeglen   4/25/2014 3:05:52 PM
NO RATINGS
This is sheer genius

True, but not my idea, was passed along in forums like this.  Apparently it was a Swiss watchmaker trick from way back.


Max The Magnificent
User Rank
Blogger
Re: I want a finger wrench!
Max The Magnificent   4/25/2014 3:00:04 PM
NO RATINGS
@GSKrasle: Each had a diffferent colour so you could tell whose board was whose, and which engineer had made a given re-work.

Wow -- impressive

<<   <   Page 2 / 5   >   >>


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Carlos Bueno

Adventures in Userland
Carlos Bueno
Post a comment
Editor’s Note: Excerpted from Lauren Ipsum: A Story About Computer Science and Other Improbable Things, author Carlos Bueno introduces us to Lauren and her adventures in Userland. ...

Max Maxfield

Tired Old iPad 2 vs. Shiny New iPad Air 2
Max Maxfield
9 comments
I remember when the first iPad came out deep in the mists of time we used to call 2010. Actually, that's only four years ago, but it seems like a lifetime away -- I mean; can you remember ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...