Breaking News
Newest First | Oldest First | Threaded View
Page 1 / 4   >   >>
User Rank
Re: GPIB cables
kinsell   12/17/2014 2:15:09 PM
Very late response, just stumbled across this discussion.

I work for a company that still sells gpib, for Linux and Windows.  When people claim things are flakey, almost always they're using cabling way out of spec.  Originally it was 2 meters per load (generally per device), but in 1987 it was cut back to 1 meter per load, when the speed was jacked up to 1 MB/sec.  After all these years, it's still astonishing how many people get it wrong.  I've seen it wrong in HP/Agilent manuals, in NI documentation, elsewhere.  People want the 'high' speed and the longer cabling, and get upset when it doesn't always work.  There's actually quite a bit of margin in the definition, but some people always push it until it breaks. 

And yes the plastic clips on Ethernet cables, and the friction fit of USB just aren't appropriate for industrial control applications.  Setting dip switches for addresses can be a pain, but it pales in comparison to the frustrations of getting a LAN device working in some environments, particularly when the IT department is half way around the world.




User Rank
I'm not the only one who says GPIB lives
MeasurementBlues   5/13/2014 2:14:19 PM
"GIPB continues to amaze people with its persistence.  While so much in the tech world is very fast to change to newer cheaper and better technology,  GPIB remains surprisingly entrenched in the test and measurement arena."

See the rest at

User Rank
Re: USB cables with screws
TonyTib   5/6/2014 1:55:27 PM
The problem is that the equipment on the other side also needs thumb screws.

I've played a bit with USB high retention force connectors (available for standard size A and size B); they help.  Even better, Ampenol makes a locking type A (PDF!) connector that works with any standard type A USB cable -- but neither type is very common, although I have seem some industrial equipment advertised with the high retention connectors.

For one customer, we had to add a little machined (which means expensive!) bracket next to the connector so they could cable-tie the USB cable to the bracket.

User Rank
USB cables with screws
Measurement.Blues   5/6/2014 12:46:21 PM

Because you seem to hate GPIB so much, here's one for using USB. Some of the complaints about USB have to do with the connectors easily pulled out. I just ran across thumbsrew USB cables.

User Rank
Moving past GPIB
DrQuine   5/3/2014 9:08:02 PM
Three decades ago, my home and lab computers required a GPIB interface to the external hard drive and certain other peripherals. As noted, the cord was expensive, inflexible, short, and required an expensive interface. The ability to stack and daisy chain the (bulky) connectors was an advantage. I'd say that for a consumer, USB has rendered the GPIB interface obsolete and irrelevant. Computer manufacturers seem to agree (indeed most laptops are thinner than the connector). In a highly technical instrumentation lab where latency rules, I'll concede they may wish to continue connecting their test and measurement devices with GPIB interfaces. 

User Rank
Re: Not Die, some better word
tom-ii   5/3/2014 6:16:20 PM
Perhaps "Pull a Patton?"  (and get run over by a horse cart)

User Rank
Not Die, some better word
_hm   5/3/2014 4:13:59 PM
GPIB served great to Test and Mesaurement communities for over three decades.

Die does not sound proper word for this veteran.

For super hero like GPIB, we should coin better phrase.

User Rank
Measurement.Blues   5/2/2014 3:15:15 PM
Here's an article I write about how VISA works with GPIB, VXI, PXI, Ethernet, and USB. Same application code, just different hardware bus.

VISA tunnels down to the kernel

Niall Gallagher
User Rank
GPIB's Compelling Advantage.
Niall Gallagher   5/2/2014 11:45:04 AM
While I share much of the sentiment regarding GPIB and its disadvantages, I have to disagree with the conclusion that it is ready to die. 

GPIB's ace is latency.   At around 30 times lower than ethernet and 4 times lower than USB, GPIB still wins when speed is critical and data transfer sizes are low.  This is generally the case in production testing.  While 1000 microseconds of latency does not seem like much, a test sequence for a complex wireless device may have up to 20,000 measurement transfers of a few bytes each.  1000us latency each time adds 20 seconds of dead time to the test sequence, reducing the throughput and increasing test cost by as much as 20%.

National Instruments has a number of papers on this subject on its website:

PXI has the advantage of very low latency and high bandwidth PCI Express, which makes it a great choice for speed critical testing such as production test.  For those using discrete instruments while concerned about test times, GPIB is still the way to go.

Kudos to Hewlett-Packard for developing an interface that has endured for over 40 years.  Calls for its demise are somewhat premature.

User Rank
Re: GPIB cables
rob18767   5/2/2014 9:38:17 AM
That's the issue. We still sell and use GPIB gear. 

The industries that do use GPIB insist on having GPIB. Therefore we have to provide GPIB or they are no longer our customers.

They have no plans to change in the immediate future. 

It's called 'giving customers what they want' as opposed to 'making engineers lives' easier' 


Page 1 / 4   >   >> Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Most Recent Comments
Like Us on Facebook
Special Video Section
Power can be a gating factor in success or failure of ...
Get to market faster and connect your next product to the ...
See how microQSFP is setting a new standard for tomorrow’s ...
The LTC3649 step-down regulator combines key features of a ...
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
Wireless Power enables applications where it is difficult ...
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...