Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 2
Lionlair
User Rank
Rookie
Error codes
Lionlair   5/6/2014 2:58:07 PM
NO RATINGS
While working for a large ATE company we had to get a customer to signoff on a 'high speed data link'.   12 bit parallel .   Their spec for the port software and cable set / whole system - was to have xxx number of block transfers without having a "non detectable" error.


I got it signed off after I got it installed and running for 2 weeks.  It ran when requested and used on three shifts.  I asked them to to sign or show me the 'non detectable error' and there was an IT guy that signed it off.   The test guys were still wondering what they were thinking of when writing the spec. 

Martin

DU00000001
User Rank
CEO
Unusual components
DU00000001   5/6/2014 2:37:26 PM
NO RATINGS
During my first jobs I had a lot of fun...

A green LED shining orange (just an error in the decimal point - 0.2 instead of 0.02 A). The effect was repeatable with this LED but not reproducible with others: they tended to emit a short flash of light when the bond wire blew.

All sorts of LETs (LE-Transistor - glowing @ 20 Amps) and SERs (Smoke Emitting Resistors).

Once we even managed to 'beam' a resistor. It vanished in a fireball the size of a cherry.
Puzzling: never found out where it rematerialized :)

anon0050695
User Rank
Rookie
Red LEDs shine yellow - for some time
anon0050695   5/6/2014 12:54:11 PM
NO RATINGS
Hello, as an intern 35 years ago when LEDs where quite new, we managed to get multiple RED LEDs to emit yellow light. The trick was to drive them with a programmable power supply set for 12V and 2.5A short circuit current. (Some experimenting with exact values needed and each batch of LEDs were slightly different.)

The record was one LED than literally burned for 3 weeks. One problem was that powering off disabled forever the short that glowed in the dark.  

And yes, the LED did make a loud noise - once - when subjected to this treatment. Two inventions in one;, NED and first generation incandescent light source.

Happy memories!

 

 

DRAMExpert
User Rank
Rookie
Memory Redundancy
DRAMExpert   5/6/2014 12:16:30 PM
NO RATINGS
In 1979, after we developed a way to use spare rows and columns of memory cells to replace defective cells in a DRAM, we needed a name for the technique.  I favored Faulty Array Repair Technique, but for some reason, Bell Labs management would not approve that name!

anon8897692
User Rank
Rookie
"Poole's Constant"
anon8897692   5/6/2014 11:45:10 AM
NO RATINGS
Long ago, I worked on a product line that required a phasing cable to be calculated, cut and installed. The guys had a long formula of degrees/360, frequency, cable velocity constant, speed of light and conversion to inches they had to type into a hand calculator every time. I reduced it down for them to a single value*degrees or something like that. They called the value "Poole's Constant".

Bill Poole

dt_hayden
User Rank
CEO
Re: Barnacles
dt_hayden   5/6/2014 10:52:58 AM
NO RATINGS
We always referred to added components as "dead bugs" as the leaded components were adhered to the board or another component with the top of the package toward the board, and resembled a deceased bug with its legs in the air.  Luckily I was never involved on a design where the dead bugs needed their own bill of materials.

zeeglen
User Rank
Blogger
Barnacles
zeeglen   5/6/2014 10:18:23 AM
NO RATINGS
The first prototype hardware PCBs usually required 'barnacles' - little leaded components that get soldered onto the PCB to fix glitches and rectify design oversights, much as marine barnacles grow on the hulls of sea-going ships.

We had a separate Bill of Materials for the barnacles, so we naturally called this the "Barnacle Bill'...

tom-ii
User Rank
Blogger
Double buffering...
tom-ii   5/6/2014 9:45:07 AM
NO RATINGS
In these modern days, the ping ponging of the video registers is called "double buffering" - I figure you know that, but someone else might not.

 

Also, aren't all diodes noise emitting?

 

I've always had some fun with noise generating circuits.  It was almost a hobby for a while.  As you can likely tell, I'm an expert at it (generating noise, that is...)

<<   <   Page 2 / 2


Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Tired Old iPad 2 vs. Shiny New iPad Air 2
Max Maxfield
6 comments
I remember when the first iPad came out deep in the mists of time we used to call 2010. Actually, that's only four years ago, but it seems like a lifetime away -- I mean; can you remember ...

<b><a href=Betajet">

The Circle – The Future's Imperfect in the Present Tense
Betajet
5 comments
The Circle, a satirical, dystopian novel published in 2013 by San Francisco-based writer Dave Eggers, is about a large, very powerful technology company that combines aspects of Google, ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...