Embedded Systems Conference
Breaking News
Newest First | Oldest First | Threaded View
User Rank
Re: PI means different things
xjordanx_#1   6/6/2014 6:52:39 PM
#MeasurementBlues this is true. The thrust of this series was the "what about DC" aspect. Something exciting to note is the accessibility of new tools, like In Circuit Design, which allow you to accurately model power plane impedances on your PCB layer stackup, and then see the effects of adding real capacitor models for decoupling. Watch this space...

User Rank
PI means different things
MeasurementBlues   5/29/2014 6:36:55 PM
To people designing boards for high-speed signals, they think of power integrity differently, mostly in terms of frequency and impedance. At icrowave frequencies, things are different. You have to deal with impedance matching, signal loss in vias, reflections, balanced differential traces, skin effect, EMI, and so on. You have to deal with PCB material characteristics such as glass weave and the fact that FR4 is running out of gas at today's frequencies.

User Rank
a 2A fuse does not open at 2A
DCH0   5/29/2014 2:37:31 PM
Remember in your PCB trace comparison that a 2A fuse does not open at 2A.  It is also a time - current function typically shown on a log-log graph.

You also have to pick which type of fuse you are modeling:  fast or slow trip, etc:

User Rank
MWagner_MA   5/29/2014 7:16:37 AM
Rules of thumb are good for planning, but with IPC-2152 available you can push the limits with confidence.  It is a very accessible document at an affordable price (when compared with many standards).  Even if your company won't pay for it - buy it for your own library.  Its worth it.

User Rank
neckdown & rule of thumb: 1mm / amp
salbayeng   5/29/2014 5:48:11 AM
Hi Ben.

I always use a rule of thumb of 1mm per amp ( I actually lay the board out in inches, but the rule is easier to remember than 40mil/amp) . (This is 2.5A per 100mil ) So on this basis you would be limited to 2A per pin for a 0.100" pitch connector.  My rule of thumb gives dT of ~ 5-10C depending on whose tables you use.

If I can't get a thick enough track to fit on the first attempt , then I start looking up the tables / graphs.

My experience indicates that proximity is an important consideration, i.e. proximity to a large island of copper, proximity to a SMD diode, proximity to another current carrying track.  Also beware of putting down a serpentine track as a current sense element, it's a lot of heat packed into a small area. 

One PCB (for a battery powered  motor control) of mine has a 3mm (120mil) track running 3/4" between two big islands of copper. Average current around 3-4amps for maybe 2minutes operation, some returned PCB's showed evidence of heat damage (probably due to a stalled motor condition at ~ 6-8A) . The odd thing is the scorching / discoloration occured only for a short distance at the exact middle of the track, so evidentally a lot of heat is conducted back to the "islands". 

I think it comes back to the aspect ratio of the "bridge" joining the "islands" , I think at 5 x width you've reached the "infinite approximation" ,  my hunch is that for an aspect ratio of 2:1 , you could double the current rating, e.g. with my 1A/mm rule , a bridge 5mm wide and 10mm long could carry 10Amp (rather than 5A for a long track). 

A bigger problem with necking of power traces is the inductance and potential EMI issues, particularly on the ground plane. I endeavour to put in some extra bridging on another layer around the neckdown, even if I have to move some components/tracks to get that bridge in.  If it's a power trace with a neckdown , then I put MLCC bypass cap to GND on either side of the neckdown.

Another trap for the unwary is the ground pin of USB connectors. Some pcb designs connect only pin4 to the gnd plane with an 8mil width track, so at the first power supply mishap on your test bench, the earth trace blows and lots of volts flow back into your PC on the remaining 3 wires. What you need to do is connect the shell of the connector to the ground plane, as the shield in the USB is good for several amps. 

Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

March 28 is Arduino Day -- Break Out the Party Hats!
Max Maxfield
Well, here's a bit of a conundrum. I just received an email from my chum David Ashton who hails from the "Unfinished Continent" Down Under. David's message was short and sweet; all he said ...

Bernard Cole

A Book For All Reasons
Bernard Cole
1 Comment
Robert Oshana's recent book "Software Engineering for Embedded Systems (Newnes/Elsevier)," written and edited with Mark Kraeling, is a 'book for all reasons.' At almost 1,200 pages, it ...

Martin Rowe

Leonard Nimoy, We'll Miss you
Martin Rowe
Like many of you, I was saddened to hear the news of Leonard Nimoy's death. His Star Trek character Mr. Spock was an inspiration to many of us who entered technical fields.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
EE Times Senior Technical Editor Martin Rowe will interview EMC engineer Kenneth Wyatt.
Flash Poll