Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
xjordanx_#1
User Rank
Author
Re: PI means different things
xjordanx_#1   6/6/2014 6:52:39 PM
NO RATINGS
#MeasurementBlues this is true. The thrust of this series was the "what about DC" aspect. Something exciting to note is the accessibility of new tools, like In Circuit Design, which allow you to accurately model power plane impedances on your PCB layer stackup, and then see the effects of adding real capacitor models for decoupling. Watch this space...

MeasurementBlues
User Rank
Author
PI means different things
MeasurementBlues   5/29/2014 6:36:55 PM
NO RATINGS
To people designing boards for high-speed signals, they think of power integrity differently, mostly in terms of frequency and impedance. At icrowave frequencies, things are different. You have to deal with impedance matching, signal loss in vias, reflections, balanced differential traces, skin effect, EMI, and so on. You have to deal with PCB material characteristics such as glass weave and the fact that FR4 is running out of gas at today's frequencies.

DCH0
User Rank
Author
a 2A fuse does not open at 2A
DCH0   5/29/2014 2:37:31 PM
NO RATINGS
Remember in your PCB trace comparison that a 2A fuse does not open at 2A.  It is also a time - current function typically shown on a log-log graph.

You also have to pick which type of fuse you are modeling:  fast or slow trip, etc:

MWagner_MA
User Rank
Author
IPC-2152
MWagner_MA   5/29/2014 7:16:37 AM
NO RATINGS
Rules of thumb are good for planning, but with IPC-2152 available you can push the limits with confidence.  It is a very accessible document at an affordable price (when compared with many standards).  Even if your company won't pay for it - buy it for your own library.  Its worth it.

salbayeng
User Rank
Author
neckdown & rule of thumb: 1mm / amp
salbayeng   5/29/2014 5:48:11 AM
NO RATINGS
Hi Ben.

I always use a rule of thumb of 1mm per amp ( I actually lay the board out in inches, but the rule is easier to remember than 40mil/amp) . (This is 2.5A per 100mil ) So on this basis you would be limited to 2A per pin for a 0.100" pitch connector.  My rule of thumb gives dT of ~ 5-10C depending on whose tables you use.

If I can't get a thick enough track to fit on the first attempt , then I start looking up the tables / graphs.

My experience indicates that proximity is an important consideration, i.e. proximity to a large island of copper, proximity to a SMD diode, proximity to another current carrying track.  Also beware of putting down a serpentine track as a current sense element, it's a lot of heat packed into a small area. 

One PCB (for a battery powered  motor control) of mine has a 3mm (120mil) track running 3/4" between two big islands of copper. Average current around 3-4amps for maybe 2minutes operation, some returned PCB's showed evidence of heat damage (probably due to a stalled motor condition at ~ 6-8A) . The odd thing is the scorching / discoloration occured only for a short distance at the exact middle of the track, so evidentally a lot of heat is conducted back to the "islands". 

I think it comes back to the aspect ratio of the "bridge" joining the "islands" , I think at 5 x width you've reached the "infinite approximation" ,  my hunch is that for an aspect ratio of 2:1 , you could double the current rating, e.g. with my 1A/mm rule , a bridge 5mm wide and 10mm long could carry 10Amp (rather than 5A for a long track). 

A bigger problem with necking of power traces is the inductance and potential EMI issues, particularly on the ground plane. I endeavour to put in some extra bridging on another layer around the neckdown, even if I have to move some components/tracks to get that bridge in.  If it's a power trace with a neckdown , then I put MLCC bypass cap to GND on either side of the neckdown.

Another trap for the unwary is the ground pin of USB connectors. Some pcb designs connect only pin4 to the gnd plane with an 8mil width track, so at the first power supply mishap on your test bench, the earth trace blows and lots of volts flow back into your PC on the remaining 3 wires. What you need to do is connect the shell of the connector to the ground plane, as the shield in the USB is good for several amps. 



Radio
NEXT UPCOMING BROADCAST
In conjunction with unveiling of EE Times’ Silicon 60 list, journalist & Silicon 60 researcher Peter Clarke hosts a conversation on startups in the electronics industry. One of Silicon Valley's great contributions to the world has been the demonstration of how the application of entrepreneurship and venture capital to electronics and semiconductor hardware can create wealth with developments in semiconductors, displays, design automation, MEMS and across the breadth of hardware developments. But in recent years concerns have been raised that traditional venture capital has turned its back on hardware-related startups in favor of software and Internet applications and services. Panelists from incubators join Peter Clarke in debate.
Flash Poll
Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Special Video Section
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...