Embedded Systems Conference
Breaking News
Comments
MeasurementBlues
User Rank
Author
Analog scope
MeasurementBlues   6/3/2014 11:17:41 PM
NO RATINGS
Arthur,

Could you use persistence to display the waveforms longer, maybe even with whough time to place your cursors?

The first cursors were horizontal and vertical lines superimposed on the display that you could use to measure the amplitude and time differences of points on the waveform. Cursors couldn't do more on an analog oscilloscope since the waveforms were transient -- they only existed for the duration of the sweep.

Arthur Pini
User Rank
Author
Re: Analog scope
Arthur Pini   6/4/2014 8:16:17 AM
NO RATINGS
Hi Martin,

You could align cursors with the waveform visually if the waveform were repetitive or you could use the persistence of the phosphor (P7 would remain visible for about 20 seconds in a dark room or with a hood).  What I intended to say was that cursors could not 'ride ' on the waveforms as they do in a digitical scope because the scope did not retain the waveform.  Having cursors move on the waveform avoids visual alignment errors that can happen with simple overlaid cursors.

Art 

gah4
User Rank
Author
Re: Analog scope
gah4   6/5/2014 9:11:12 PM
NO RATINGS
In between the traditional analog scope and the digital version was the storage CRT. The elecron (charge) image would be stored on the screen, and made visible with a flood electron gun. 

But yes, with cheap digital storage, that is the best way to do it.

bikeron
User Rank
Author
Grids
bikeron   6/12/2014 2:33:49 PM
NO RATINGS
Grids were on scopes long before the 70's.

http://en.wikipedia.org/wiki/Tektronix_analog_oscilloscopes

 Here is from 1950's!

http://richardsears.wordpress.com/2012/01/07/near-the-beginning-of-an-era-the-tektronix-511a/

Arthur Pini
User Rank
Author
Re: Grids
Arthur Pini   6/12/2014 4:56:54 PM
NO RATINGS
Hi bikeron,

Thanks for the great reference. It certainly shows the state of the art on the 1950's.

I agree that grids were associated with scopes from the very first commercial models.

The reference to the 1970's in the article was associated with the advent of cursors in scopes. 

 

Regards

Art

 

 



Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...