Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 3 / 3
elizabethsimon
User Rank
Author
Re: Ac coupling
elizabethsimon   6/13/2014 5:07:57 PM
NO RATINGS
The good people at Apple, knowing that folk will merrily plug the headphone jack into all kinds of speakers probably already included the capacitor in series to get rid of any DC offset. At least that's what I'd do if I was in charge....

Max The Magnificent
User Rank
Author
Re: Ac coupling
Max The Magnificent   6/13/2014 1:22:04 PM
NO RATINGS
@antedeluvian: I am surprised there wasn't a DC bias...

Sonce I know so little about audio, I wouldn't have been surprised either way :-)

Max The Magnificent
User Rank
Author
Re: Ac coupling
Max The Magnificent   6/13/2014 1:20:52 PM
NO RATINGS
@Aubrey: If you want to get rid of the DC component of the signal just use a capacitor in series with the signal.

Absolutally -- in fact the circuit I'm using with the MSGEQ7 chips from SparkFun has just such a decoupling capacitor (I'll be discussing thsi circuit in a future column) -- the main thing at this point is that I wanted to use my frequency generator to replicate the signal coming out of the iPad -- if there had been a DC offset I woudl have replicated it, even though my series capacitor would have (effectively) taken it out again.

antedeluvian
User Rank
Author
Ac coupling
antedeluvian   6/13/2014 11:36:07 AM
NO RATINGS
Max

If you want to get rid of the DC component of the signal just use a capacitor in series with the signal. On t'other side you need a largish resistor to ground if you are looking to ground reference it, but you can bias it to whatever DC value you like by using a resistor divider.

Remember to choose the value of the capacitor for a low impedance and that it will interrelate with the aformentioned resistors. Today you can get ceramic caps in the 10uF range or more, but in the old days you had to use polarized ones leading you to try and figure out which side should be positive, Of course you could depolarize by placing two in series in opposing polarity.

I am surprised there wasn't a DC bias. From my understanding (which is very little) of a TI seminar on the audio amplifiers in phones etc. the voltage swing is doubled by driving the output in opposite phases across the speaker, much like the driver on RS485 and as I recall it ran on a single supply. Obviously I misunderstood.

 

 

<<   <   Page 3 / 3


Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...