Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
Page 1 / 3   >   >>
zeeglen
User Rank
Author
Re: Whattup? What was the conclusion? ;-)
zeeglen   7/10/2014 7:25:13 PM
NO RATINGS
@ Lee

Answers are in Part 2 here:

http://www.eetimes.com/author.asp?section_id=36&doc_id=1322984

Max, could you insert a link in Part 1 to get to part 2?

studleylee
User Rank
Author
Whattup? What was the conclusion? ;-)
studleylee   7/10/2014 5:35:51 PM
NO RATINGS
Hi, just wanted to know if an answer was posted.

Thanks, -Lee

studleylee
User Rank
Author
I guesss...
studleylee   7/3/2014 6:28:08 PM
NO RATINGS
Q's drive inductive loads probably relays or bulbs . They have snubbers and flyback protection for HV( 120v-ish loads commened to a positive rail ).

Alarm is logic sum of 2 peaking detectors if either 'load voltage at Q's' doesnt toggle during the rc time constant, the alarm will activate( active low).

555 tau ~ which would tell the expected timeout tested for.

-Lee Studley ( edited this a couple of times :-)

Wnderer
User Rank
Author
Re: Puzzle
Wnderer   7/3/2014 9:48:30 AM
NO RATINGS
@eetcowie

I don't see why you would need to prevent the two transistors from turning on at the same time in a motor. I think a two phase motor would have its coils driven 90 degrees out of phase not 180 degrees.

Yvon.H
User Rank
Author
Re: What could it be?
Yvon.H   7/3/2014 7:56:28 AM
NO RATINGS
It looks to me as a circuit to drive a ring signal from a telephone station based on the 48V, the frequency and the output voltage. 

 

Navelpluis
User Rank
Author
Driving a small transformer
Navelpluis   7/3/2014 4:51:30 AM
NO RATINGS
As seen from the protection stuff on the outputs I think it is driving a small transformer, probably center tapped. This transformer is driving 2 nasty devices capable of giving a big burst of energy back to the primary drivers. It might be 2 enormous MOSFET's or IGBT's that -depending on the speed and load- are able to destroy direct logic driving. I think at least I should win half a pint of lukewarm beer....(Yikes! ;-)

zeeglen
User Rank
Author
Re: Aha! It's a trick question!
zeeglen   7/2/2014 8:28:33 PM
@betajet My other off-beat guess is a flipper torpedo, with a single tail fin powered by alternating electromagnets.

This would be great if used on one of those helium-filled air-floating sharks that Max wrote about a while back.  The 400 Hz tone would be a bit annoying, but at least would give warning that the beast was approaching - from miles away!  And could also double as a fire alarm bell if two gongs were located near the tailfin.  :^}

As for the red connection points, thay are just part of the net naming symbol in TinyCAD schematic drawing software.  One has to position the red connection point on the wire to give it a name, so there really is a connection.

 

betajet
User Rank
Author
Aha! It's a trick question!
betajet   7/2/2014 2:22:20 PM
If you look closely at the schematic, you'll see that the connection points on the four off-page connectors are red, which means they're not actually connected.  [PCB designer rule #1: never trust the schematic.  Always check the netlist!]  This means there's no power in, no connection to loads be they inductive or otherwise, and no connection to ~Alarm.

Actually, I'm going to go with a couple of off-beat guesses.  Since the input voltage is +48V, that sounds like four 12V batteries, which is a common configuration battery back-up of serious electronics.  I'm guessing a really loud alarm bell, actually a pair of bells with a hammer between them which is driven by two electromagnets alternating at 400 Hz.  I mean really loud, the kind of alarm that clears a building in case of fire.

My other off-beat guess is a flipper torpedo, with a single tail fin powered by alternating electromagnets.  The reason for a flipper rather than a circular propeller is so that it has a passive sonar signature that sounds like a fish.

jmumford913
User Rank
Author
Re: What could it be?
jmumford913   7/2/2014 2:07:17 PM
NO RATINGS
I'm going to guess, based on the 110V zener diodes in the output, that the load is around 45mA (since that's what the zeners are going to be conducting when the JFETs are off and the opposite rail is active).

antedeluvian
User Rank
Author
Re: Puzzle
antedeluvian   7/2/2014 12:55:02 PM
NO RATINGS
Ivan

The alarm goes low whenever the pulsing AC voltage quits on either EdgeConn1 and/or EdgeConn2. This means that if the 555 fails, or the external inductors blow open, or the external voltage being supplied from somewhere to the inductor-loads (may not be the same 48v+ supply) fails, then the alarm goes low (asserted).

That makes much more sense. I missed that red bar over the ALARM.

Page 1 / 3   >   >>


Radio
LATEST ARCHIVED BROADCAST
As data rates begin to move beyond 25 Gbps channels, new problems arise. Getting to 50 Gbps channels might not be possible with the traditional NRZ (2-level) signaling. PAM4 lets data rates double with only a small increase in channel bandwidth by sending two bits per symbol. But, it brings new measurement and analysis problems. Signal integrity sage Ransom Stephens will explain how PAM4 differs from NRZ and what to expect in design, measurement, and signal analysis.

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Like Us on Facebook
Special Video Section
The LTC®6363 is a low power, low noise, fully differential ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...
The LT®3042 is a high performance low dropout linear ...
Chwan-Jye Foo (C.J Foo), product marketing manager for ...
The LT®3752/LT3752-1 are current mode PWM controllers ...
LED lighting is an important feature in today’s and future ...
Active balancing of series connected battery stacks exists ...
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...