Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 2 / 3   >   >>
Max The Magnificent
User Rank
Blogger
Re: Resistor value tools
Max The Magnificent   7/10/2014 11:33:21 AM
NO RATINGS
@David: ... as you know I am a confirmed scrounger of bits from old boards.

I didn't know you'd been confirmed -- I thought you still maintained your amateur status LOL

David Ashton
User Rank
Blogger
Re: Resistor value tools
David Ashton   7/9/2014 9:39:29 PM
NO RATINGS
@Antedeluvian - as you know I am a confirmed scrounger of bits from old boards.  While I very rarely remove resistors these days unless they are very easy, I do see a lot of them and can confirm that (for thru-hole components anyway) the vast majority of them, even though they are 1% resistors, confirm to E12 values (not even E24, though you do see some of those).  The same seems to apply to SMD resistors though I cannot speak with the same experience on those - they are usually so small it's a pain to check the values.

I guess there is a good reason for this - for (say) LED dropping resistors or pull-up resistors (which covers a good deal of what resistors are used for theses days) the exact value is not critical at all, so by sticking to E12 values, manufacturers don't need large (and expensive) inventories. 

 

David Ashton
User Rank
Blogger
Re: Timings
David Ashton   7/9/2014 6:21:47 PM
NO RATINGS
@Max....I think that's better....but really this should be in the datasheet - as someone else pointed out the datasheet could have a lot more info in it.

antedeluvian
User Rank
Blogger
Resistor value tools
antedeluvian   7/9/2014 2:00:21 PM
NO RATINGS
Max

The color code for a 68Ω resistor (the three colored bands on the resistor) is blue-gray-black. You can find all sorts of information about resistor color codes on the Internet, including this rather nice resistor color code converter. Another useful tool is this LED resistor calculator, which rounds the result to the closest resistance value that is actually available.

Both these tools work with, at best, 5% resistor values, the E24 range. I haven't looked at hobby distributors recently but we are finding it increasingly difficult to find 5% resistors (that were originally used to pinch some pennies), without a minimum order. It seems the technology has improved to the point where 1% reistsors are easy enough to make without sufficient rejects to justify a 5% range. It is easy enough to change the values to the E96 range- it just means tons of ECNs.

At one point, I did read that 0.1% resistors were becoming cheaper, but they were going to revert back to the E24 series rather than the E96. I am not sure where that is right now.

On a self-serving note I should mention that it is easy enough to do these calculations with any computer based tool- I have used and written about using Excel for electronics extensively. Using some variation of the LOOKUP function and a table of resistor values, it is easy enough to find the nearest standard resistor value. My latest blog on Planet Analog goes a step further and is about finding the best match for a resistor pair using standard values (as in the gain of an op-amp or the voltage of an LM317). Excel-Optimizing Resistor Ratios Part 1 and Part 2. You can see all my blogs on Excel interspersed amongst some others here.

jambrose950
User Rank
Rookie
Re: New devices: MSGEQ7
jambrose950   7/9/2014 1:15:18 PM
NO RATINGS

The Mixed Signal Integration MSGEQ7 has a linear output. 

Max The Magnificent
User Rank
Blogger
Re: New devices
Max The Magnificent   7/9/2014 12:01:30 PM
NO RATINGS
@antedeluvian: I must say that in this day and age of word processing and electronic publishing that their data sheets are decidedly "retro" to say the very least.

They aren't alone. Some companies do a really good job at this. Others ... not so much. The datasheets from Mixed Signal Integration are distinguished as much by the useful information they leave out as by the information they actually decide to include.

For example, as David Ashton points out, from the data sheet we don't know if the spectrum values generated by the chip are linear or logarithmic. This really is a key piece of information (I'm going to determine it experimentally thsi coming weekend).

Max The Magnificent
User Rank
Blogger
Re: Moving the filters in
Max The Magnificent   7/9/2014 11:57:48 AM
NO RATINGS
@mithrandit: Yup, it's the PSoC4 kit. Have it close at hand and I'm used to the IDE so it'll be quick.

I have an unopened PSoC 4 Pioneer Kit sitting on my desk -- it's staring at me making me feel guilty -- I'd love to see your C code when you've written it.

Max The Magnificent
User Rank
Blogger
Re: Timings
Max The Magnificent   7/9/2014 11:56:02 AM
NO RATINGS
@David: I notice the minimum strobe pulse width is less (18us) than the settling time (36us) - which implies you can read the data even if the strobe has gone back high? (ie you could actually read data during the purple times in your diagram?)


David -- I decided this point was important enough that I've gone back and added some stuff to the main column (page 1) -- take a look and see what you think.

antedeluvian
User Rank
Blogger
New devices
antedeluvian   7/9/2014 11:40:09 AM
NO RATINGS
Max

I love finding new manufacturers of speciality devices, so I looked up the manuafacturer of the MSGEQ7. They are called Mixed System Integration with some interesting devices. I will keep them in mind. They seem to have been in business for 10 years or more, but I must say that in this day and age of word processing and electronic publishing that their data sheets are decidedly "retro" to say the very least.

mithrandir
User Rank
Rookie
Re: Moving the filters in
mithrandir   7/9/2014 11:36:06 AM
NO RATINGS
Yup, it's the PSoC4 kit. Have it close at hand and I'm used to the IDE so it'll be quick.

 

I'll keep you posted.

<<   <   Page 2 / 3   >   >>


Flash Poll
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Juggling a Cornucopia of Projects
Max Maxfield
2 comments
I feel like I'm juggling a lot of hobby projects at the moment. The problem is that I can't juggle. Actually, that's not strictly true -- I can juggle ten fine china dinner plates, but ...

Larry Desjardin

Engineers Should Study Finance: 5 Reasons Why
Larry Desjardin
27 comments
I'm a big proponent of engineers learning financial basics. Why? Because engineers are making decisions all the time, in multiple ways. Having a good financial understanding guides these ...

Karen Field

July Cartoon Caption Contest: Let's Talk Some Trash
Karen Field
127 comments
Steve Jobs allegedly got his start by dumpster diving with the Computer Club at Homestead High in the early 1970s.

Jeremy Cook

Inspection Rejection: Why More Is Less in a Vision System
Jeremy Cook
3 comments
Albert Einstein has been quoted as saying, "Everything should be as simple as possible, but not simpler." I would never claim to have his level of insight -- or such an awesome head of ...

Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)