Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
bec0
User Rank
Rookie
Re: The issue of cost
bec0   7/18/2014 1:54:16 PM
NO RATINGS

@resistion: I am not sure I understood your comments, but I will try to comment below. Also, there will be lots more info at the upcoming IEEE S3S Conference. See you there.

Cost savings: Yup, any added degree of freedom will eventually approach an asymptote. But we have given designers /EDA another degree...lots to gain before the parabola starts winning. Also, why not mix layers? Two logic layers (for logic redundancy), then one or more memory (maybe NV), then two more logic. Cool on both sides if needed. Might be a trick to mitigate congestion and help heat.

Heat: The IEDM work ran both layers (substrate and monolithic 2nd layer) really hard and hot, and reasonable cooling was accomplished with the interlayer vias and power grids. The larger issue was getting a big enough heat sink capability...had to go to liquid cooling to get all the watts out of the stack. But it's even worse for 2D, as there are more C and R power losses to overcome with the longer wires; hence, more power to accomplish the calculaton/task. And I can't imagine that we are going to be able to immerse our mobile systems in chilled mineral oil, as the Japanese did with their winning supercomputer. Rather, mobile/battery designs will be by lower Vcc, smart power usage, parallelism, etc....

BC

 

resistion
User Rank
CEO
Re: The issue of cost
resistion   7/15/2014 10:45:41 PM
NO RATINGS
Thanks for the referred links. I suppose if you can eliminate a fraction of the line connections (replacing them with vias) with each stacking iteration, there can be some savings. This could explain the asymptotic behavior. But for the heat removal, in the case that the layer on the heat sink is generating heat, the boundary condition no longer favors heat removal.

bec0
User Rank
Rookie
Re: The issue of cost
bec0   7/15/2014 11:35:31 AM
NO RATINGS
Great comments @resistion and @alex_m1. As to cost savings, the footprint is 25% of the original and the total silicon area is 50% when folding a logic design into two layers. Why? Mostly repeaters/buffer savings and transistor sizes....average wire length in the chip goes down. This blog goes thru some of the details http://www.monolithic3d.com/3d-ic-edge1.html. And both layers are mono-crystalline silicon...with layer transfer the cost of the top layer mono-Si is amortized over the 10-20 times you use the donor wafer. Bottom line...it looks just like a node of scaling.

Yes, on the 2nd and subsequent layers, one gets SOI naturally in the monolithic process flow...cost savings and performance benefits. However, one has to deal with improving the heat conduction.  Heat removal is a matter of getting a high enough lateral and vertical conduction to a sufficient heat-sink to overcome the operational heat generation. This blog talks to this with reference to an IEDM2012 paper by Stanford http://www.monolithic3d.com/blog/can-heat-be-removed-from-3d-ic-stacks on how to do that. Lateral is solved by rigorously using the Vss/Vdd network to move the heat laterally as if the 2nd layer 'substrate' is bulk Si, and the vertical conduction is taken care of by the high density of available vertical 'heat pipes' of monolithic 3D...10e6-10e8/cm2.  BC

resistion
User Rank
CEO
Re: The issue of cost
resistion   7/15/2014 10:35:51 AM
NO RATINGS
I see the graphs, thanks, but the only way there is any savings is if the added silicon is not as decent as the single crystal substrate (like cheap polysilicon not epitaxial). But then you're sacrificing performance, not really scaling down good performance.

alex_m1
User Rank
CEO
Re: The issue of cost
alex_m1   7/15/2014 7:58:39 AM
NO RATINGS
@resistion: [1] includes a image depicting suppoosed cost advantages of monolithic 3d. Saving for 1st layer are 25% , for 4th layer around 18% , and further there's only little savings.

http://www.eetimes.com/author.asp?section_id=36&doc_id=1320411

resistion
User Rank
CEO
The issue of cost
resistion   7/15/2014 6:41:42 AM
NO RATINGS
I'm not sure if it was glossed over, but isn't the cost easily larger than the sum of processing the individual silicon layers?

Also possibly glossed over, the accumulation of heat, especially with SOI?



Top Comments of the Week
Flash Poll
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Tired Old iPad 2 vs. Shiny New iPad Air 2
Max Maxfield
7 comments
I remember when the first iPad came out deep in the mists of time we used to call 2010. Actually, that's only four years ago, but it seems like a lifetime away -- I mean; can you remember ...

<b><a href=Betajet">

The Circle – The Future's Imperfect in the Present Tense
Betajet
5 comments
The Circle, a satirical, dystopian novel published in 2013 by San Francisco-based writer Dave Eggers, is about a large, very powerful technology company that combines aspects of Google, ...

Martin Rowe

Make This Engineering Museum a Reality
Martin Rowe
Post a comment
Vincent Valentine is a man on a mission. He wants to make the first house to ever have a telephone into a telephone museum. Without help, it may not happen.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Doug Bailey, VP of marketing at Power Integrations, gives a ...
See how to ease software bring-up with DesignWare IP ...
DesignWare IP Prototyping Kits enable fast software ...
This video explores the LT3086, a new member of our LDO+ ...
In today’s modern electronic systems, the need for power ...