Breaking News
Comments
Oldest First | Newest First | Threaded View
alex_m1
User Rank
Author
How ?
alex_m1   7/17/2014 12:55:23 PM
NO RATINGS
How does the shortness of exposure time affects wafer/hour of euv ?

R_Colin_Johnson
User Rank
Author
Re: How ?
R_Colin_Johnson   7/17/2014 1:50:50 PM
NO RATINGS
There's a lot more to it than the exposure time. Researcher using commercially available tools today are producing less than 100 wafers a day while still in debugging mode. The optimists among them are hoping for 500 wafers a day by 2015 and 1,500 wafers per day at the 10 nanometer node slated by 2017.

resistion
User Rank
Author
Misguided
resistion   7/17/2014 8:22:19 PM
NO RATINGS
A "long" exposure time is needed to guarantee sufficient photon density to define an image with statistical robustness. So 15 mJ/cm2 is already too low.

Also if it's negative tone resist due to crosslinking it's going to be more defect sensitive on the contact or metal layers.

DrFPGA
User Rank
Author
Or just use
DrFPGA   7/20/2014 1:46:01 AM
NO RATINGS
Self assembly... https://ecs.confex.com/ecs/226/webprogram/Paper43140.html

resistion
User Rank
Author
DSA
resistion   7/20/2014 10:34:28 AM
NO RATINGS
Directed self-assembly is a no-brainer for HDD, for their bit-patterned media technology, since it is defect tolerant. Otherwise you might worry if your trench is a little narrow, a self-assembled line inside might get squeezed out.

R_Colin_Johnson
User Rank
Author
Re: Misguided
R_Colin_Johnson   7/21/2014 5:04:59 PM
NO RATINGS
I didn't know the answer to your question so I asked the author, here's what he said: Dear Colin, The commenter is partially right. Shot noise (statistical robustness) is a concern for high sensitivity resists. Length of exposure is not what is important but the total dose. I think they understand this as they put long in quotes ad reported the right units of mJ/cm2. However, it is an open area of research as to whether roughness and loss of resolution is a result of shot noise or other inhomogeneities in the process. I don't think we are at the shot noise limit yet. Also as we approach the shot noise limit, material reorganization during the bake and development steps may mitigate the problem by smoothing or filtering the result. In conclusion, we need high sensitivity resists because of expense issues with the exposure tools. Shot noise is not a killer and managing the roughness resulting from the exposure is part of future resist design. I am not sure how significant the penalty for negative tone on the metal layers is. Definitely the champion resist is positive tone and there is preference for positive tone but that preference can be displaced with superior performance if it comes. A "long" exposure time is needed to guarantee sufficient photon density to define an image with statistical robustness. So 15 mJ/cm2 is already too low. Also if it's negative tone resist due to crosslinking it's going to be more defect sensitive on the contact or metal layers.

resistion
User Rank
Author
Re: Misguided
resistion   7/21/2014 5:31:04 PM
NO RATINGS
The shot noise issue is more about dose control and critical dimension (CD) response to dose. Higher sensitivity means CD will be more sensitive to shot noise dose variations like few %. This is more significant for smaller CD, where a few % would eat up the tolerance.



Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
NEXT UPCOMING BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Are the design challenges the same as with embedded systems, but with a little developer- and IT-skills added in? What do engineers need to know? Rick Merritt talks with two experts about the tools and best options for designing IoT devices in 2016. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.
Like Us on Facebook
Special Video Section
The quality and reliability of Mill-Max's two-piece ...
01:34
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...
The LTC®4015 is a complete synchronous buck controller/ ...
10:35
The LTC®2983 measures a wide variety of temperature sensors ...
The LTC®3886 is a dual PolyPhase DC/DC synchronous ...
The LTC®2348-18 is an 18-bit, low noise 8-channel ...