Breaking News
Newest First | Oldest First | Threaded View
Ron Neale
User Rank
Re: Mix of PCM and DVD for practical applications
Ron Neale   7/26/2014 12:09:56 PM
Semyon; Thanks for the reminder. I cannot find a copy of the paper in my personal archives. From memory, I thought that work was for permanent face-to-face bonding, or surface mount, implying the bonded chip would be smaller than the chip to which it was bonded to enable connections to the package and then on to the outside world. Also was the beam IR and focussed through the silicon or from the side??? Perhaps you could share with EETimes readers a little more detail. Another personal opto application, a long time ago (applied 1968) I did obtain a patent (US 3,634,927) for writing, using a laser or light beam, crystallized lines of conducting interconnect on an IC which had been pre-coated with an insulating amorphous or phase change material. I think that was the precursor to the work where light was used to write crystallized data on discs.

I think the work I reported in my article above is about is eventually switching and redirecting modulated beams of different colors.

Semyon Savransky
User Rank
Mix of PCM and DVD for practical applications
Semyon Savransky   7/26/2014 10:49:48 AM
Another potential kind of optoelectronic application of phase-change alloys (PCA) can be in permanent interconnections within and between IC chips. For example PCA can be used in ultra-cheap interposers for 2.5D- and 3D-IC assembly (

Ron Neale
User Rank
Re: Stoppers?
Ron Neale   7/22/2014 5:12:33 PM
 Janine I am certainly excited about the possibility of using these devices as intra and inter chip optical switches and the range of possible products the work might spawn.
I think the first step and challenge must be to produce large numbers of planar discrete ITO/GST/ITO PCMs with 7nm GST films. I think the tools for electrical characterisation of those devices are readily available see and there is a good experience base to draw on. If it was me, I would initially concentrate on those measurements. Then add the platinum mirror and start looking at the optical characteristics when some reasonable level of repeatability and stability has been achieved. Or even do both things in parallel. I guess the simplest optical experiment would be to fabricate the discrete devices with the GST in the amorphous state and use a hot plate to crystallize the material and explore the reproducibility of the colour change. Then do the same experiment after some fixed number of write/erase cycles. I think it is going to get very interesting when the time comes to do the equivalent of PCM elevated temperature data retention, which I suppose we will have to call elevated temperature colour retention for the Opto-PCMs (OPCMs).

User Rank
JanineLove   7/22/2014 3:59:46 PM
Hi Ron, you seem really enthusiastic about this project. I'm wondering about this part: "This will require a full characterization, with special attention to write/erase lifetime, switching times, power dissipation, and data retention, added to which must be the optical characterization for each step in the development -- all of which is a non trivial undertaking." What do you think the biggest challenge will be to moving characterization forward? Do we have the T&M tools to handle this? Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
Power can be a gating factor in success or failure of ...
Get to market faster and connect your next product to the ...
See how microQSFP is setting a new standard for tomorrow’s ...
The LTC3649 step-down regulator combines key features of a ...
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
Wireless Power enables applications where it is difficult ...
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
The LT8602 has two high voltage buck regulators with an ...
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...