Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
Ron Neale
User Rank
Blogger
Re: Mix of PCM and DVD for practical applications
Ron Neale   7/26/2014 12:09:56 PM
NO RATINGS
Semyon; Thanks for the reminder. I cannot find a copy of the paper in my personal archives. From memory, I thought that work was for permanent face-to-face bonding, or surface mount, implying the bonded chip would be smaller than the chip to which it was bonded to enable connections to the package and then on to the outside world. Also was the beam IR and focussed through the silicon or from the side??? Perhaps you could share with EETimes readers a little more detail. Another personal opto application, a long time ago (applied 1968) I did obtain a patent (US 3,634,927) for writing, using a laser or light beam, crystallized lines of conducting interconnect on an IC which had been pre-coated with an insulating amorphous or phase change material. I think that was the precursor to the work where light was used to write crystallized data on discs.

I think the work I reported in my article above is about is eventually switching and redirecting modulated beams of different colors.

Semyon Savransky
User Rank
Rookie
Mix of PCM and DVD for practical applications
Semyon Savransky   7/26/2014 10:49:48 AM
NO RATINGS
Another potential kind of optoelectronic application of phase-change alloys (PCA) can be in permanent interconnections within and between IC chips. For example PCA can be used in ultra-cheap interposers for 2.5D- and 3D-IC assembly (http://www.smta.org/knowledge/proceedings_abstract.cfm?PROC_ID=3898).

Ron Neale
User Rank
Blogger
Re: Stoppers?
Ron Neale   7/22/2014 5:12:33 PM
NO RATINGS
 Janine I am certainly excited about the possibility of using these devices as intra and inter chip optical switches and the range of possible products the work might spawn.
I think the first step and challenge must be to produce large numbers of planar discrete ITO/GST/ITO PCMs with 7nm GST films. I think the tools for electrical characterisation of those devices are readily available see
http://www.eetimes.com/author.asp?section_id=36&doc_id=1323076 and there is a good experience base to draw on. If it was me, I would initially concentrate on those measurements. Then add the platinum mirror and start looking at the optical characteristics when some reasonable level of repeatability and stability has been achieved. Or even do both things in parallel. I guess the simplest optical experiment would be to fabricate the discrete devices with the GST in the amorphous state and use a hot plate to crystallize the material and explore the reproducibility of the colour change. Then do the same experiment after some fixed number of write/erase cycles. I think it is going to get very interesting when the time comes to do the equivalent of PCM elevated temperature data retention, which I suppose we will have to call elevated temperature colour retention for the Opto-PCMs (OPCMs).

JanineLove
User Rank
Blogger
Stoppers?
JanineLove   7/22/2014 3:59:46 PM
NO RATINGS
Hi Ron, you seem really enthusiastic about this project. I'm wondering about this part: "This will require a full characterization, with special attention to write/erase lifetime, switching times, power dissipation, and data retention, added to which must be the optical characterization for each step in the development -- all of which is a non trivial undertaking." What do you think the biggest challenge will be to moving characterization forward? Do we have the T&M tools to handle this?



Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Book Review: Deadly Odds by Allen Wyler
Max Maxfield
11 comments
Generally speaking, when it comes to settling down with a good book, I tend to gravitate towards science fiction and science fantasy. Having said this, I do spend a lot of time reading ...

Martin Rowe

No 2014 Punkin Chunkin, What Will You Do?
Martin Rowe
1 Comment
American Thanksgiving is next week, and while some people watch (American) football all day, the real competition on TV has become Punkin Chunkin. But there will be no Punkin Chunkin on TV ...

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
14 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Martin Rowe

Book Review: Controlling Radiated Emissions by Design
Martin Rowe
1 Comment
Controlling Radiated Emissions by Design, Third Edition, by Michel Mardiguian. Contributions by Donald L. Sweeney and Roger Swanberg. List price: $89.99 (e-book), $119 (hardcover).