Embedded Systems Conference
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 10 / 10
dt_hayden
User Rank
Author
consumer versus industrial
dt_hayden   8/13/2014 2:37:02 PM
NO RATINGS
In general, grounding yourself through a piece of (consumer grade) electronic equipment for ESD control seems like a not so good idea.  You are making assumptions about the goodness of that ground and assuming the equipment can withstand discharges into that point.  If you are sure only the wriststrap connection touches the "ground" point, then currents are limited by the resistor in the strap anyway and less of a worry.  If you grab the "ground" to make your connection, you could potentially make a direct discharge at that point. 

Having said that, Tek scopes I have used in the past had a "grounded" banana jack on the front panel which I plugged into for ESD management.  My thinking was since it was industrial gear, Tek designs robust equipment, and the point was probably put there for that purpose, it was fine. 

If you are only dealing with isolated portable gear, I think it is more important to equalize potential to the gear, rather than to ground.  .I have clipped onto grounds of gear in these cases.  In this case, some (all?) soldering ground tips are grounded, so beware when soldering.

Max The Magnificent
User Rank
Author
Re: Maybe...
Max The Magnificent   8/13/2014 2:34:55 PM
NO RATINGS
@Crusty: I get over stretching the colied cable of the wristband by having a multiple socket strip...

Actually, that's not a bad idea -- I usually have a couple of these lying around -- but I'm going to check the USB thing first...

antedeluvian
User Rank
Author
Notebook??
antedeluvian   8/13/2014 2:34:46 PM
NO RATINGS
Max

I hope I am not alone in noticing that a notebook can run on batteries, in which case you have no ground at all.

Crusty1
User Rank
Author
Re: Maybe...
Crusty1   8/13/2014 2:28:15 PM
NO RATINGS
Hi Max : I get over stretching the colied cable of the wristband by having a multiple socket strip, on a lead from the wall socket, in England these are very cheap from Ikea. The soldering Iron and powers supply go into two of the free sockests leaving me with two other sockets for wristband and antistatic mat.

This approach any use?

Max The Magnificent
User Rank
Author
Re: Maybe...
Max The Magnificent   8/13/2014 1:57:42 PM
NO RATINGS
@Duane: In most US wall sockets, the screw that holds the outlet plate on is grounded. If that's the case, you could just connect to that screw for your earth ground.

But they I still have the probem that the wall socket is quite a way from the table -- unless I attach a loong piece of wire -- and I don;t fancy attaching and detaching that wire each time I want to play with my electronics...

Max The Magnificent
User Rank
Author
Re: Maybe...
Max The Magnificent   8/13/2014 1:55:34 PM
NO RATINGS
@Duane: Just to be sure, I ran it past a couple of my ESD experts here [...] if it's less than 1 ohm, you're good to go.

Potential Happy Dance -- I'll check thsi as soon as I get home this evening an report back in the morning...

Duane Benson
User Rank
Author
Re: Maybe...
Duane Benson   8/13/2014 1:54:46 PM
NO RATINGS
In most US wall sockets, the screw that holds the outlet plate on is grounded. If that's the case, you could just connect to that screw for your earth ground.

Duane Benson
User Rank
Author
Re: Maybe...
Duane Benson   8/13/2014 1:51:10 PM
NO RATINGS
Just to be sure, I ran it past a couple of my ESD experts here.

Connect your ohm meter between the ground wire you have coming out of that USB cable, and the ground pin on the AC power plug (with the AC power cord unplugged). If it's less than 1 ohm, you're good to go.

Max The Magnificent
User Rank
Author
Re: Maybe...
Max The Magnificent   8/13/2014 1:41:43 PM
NO RATINGS
@Duane: You might not actually be connected to ground.

I'm not wearing my smiley face -- how can I determine if I am or am not...?

Duane Benson
User Rank
Author
Maybe...
Duane Benson   8/13/2014 1:38:09 PM
NO RATINGS
You might not actually be connected to ground. You have DC going from the power supply to the notebook. Depending on how the power supply is isolated or not isolated, grounded or not grounded, there may not be a direct connection to an earth ground.

<<   <   Page 10 / 10


Top Comments of the Week
Like Us on Facebook

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

March 28 is Arduino Day -- Break Out the Party Hats!
Max Maxfield
7 comments
Well, here's a bit of a conundrum. I just received an email from my chum David Ashton who hails from the "Unfinished Continent" Down Under. David's message was short and sweet; all he said ...

Bernard Cole

A Book For All Reasons
Bernard Cole
1 Comment
Robert Oshana's recent book "Software Engineering for Embedded Systems (Newnes/Elsevier)," written and edited with Mark Kraeling, is a 'book for all reasons.' At almost 1,200 pages, it ...

Martin Rowe

Leonard Nimoy, We'll Miss you
Martin Rowe
5 comments
Like many of you, I was saddened to hear the news of Leonard Nimoy's death. His Star Trek character Mr. Spock was an inspiration to many of us who entered technical fields.

Rich Quinnell

Making the Grade in Industrial Design
Rich Quinnell
16 comments
As every developer knows, there are the paper specifications for a product design, and then there are the real requirements. The paper specs are dry, bland, and rigidly numeric, making ...

Special Video Section
After a four-year absence, Infineon returns to Mobile World ...
A laptop’s 65-watt adapter can be made 6 times smaller and ...
An industry network should have device and data security at ...
The LTC2975 is a four-channel PMBus Power System Manager ...
In this video, a new high speed CMOS output comparator ...
The LT8640 is a 42V, 5A synchronous step-down regulator ...
The LTC2000 high-speed DAC has low noise and excellent ...
How do you protect the load and ensure output continues to ...
General-purpose DACs have applications in instrumentation, ...
Linear Technology demonstrates its latest measurement ...
10:29
Demos from Maxim Integrated at Electronica 2014 show ...
Bosch CEO Stefan Finkbeiner shows off latest combo and ...
STMicroelectronics demoed this simple gesture control ...
Keysight shows you what signals lurk in real-time at 510MHz ...
TE Connectivity's clear-plastic, full-size model car shows ...
Why culture makes Linear Tech a winner.
Recently formed Architects of Modern Power consortium ...
Specially modified Corvette C7 Stingray responds to ex Indy ...
Avago’s ACPL-K30T is the first solid-state driver qualified ...
NXP launches its line of multi-gate, multifunction, ...
Radio
LATEST ARCHIVED BROADCAST
EE Times Senior Technical Editor Martin Rowe will interview EMC engineer Kenneth Wyatt.
Flash Poll