Design Con 2015
Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 9 / 10   >   >>
mhrackin
User Rank
CEO
Re: Maybe...
mhrackin   8/13/2014 3:45:57 PM
NO RATINGS
I don't know what flavor notepad you are using, but I have a number of Lenovo Thinkpad power supplies on my desk right now, and i noticed that they have a TWO-WIRE UNGROUNDED (and unpolarized) AC plug.  I also have some ancient Dell ones with 3-wire cords.  Obviously, there's no point in ohming out the Thinkpad ones as there is NO input ground.  The Dells do have the ground continuous (1.2 ohms) to the shell of the DC power plug.  However, these are REALLY old (from XP PCs) so your results may differ.

Max The Magnificent
User Rank
Blogger
Re: consumer versus industrial
Max The Magnificent   8/13/2014 2:41:38 PM
NO RATINGS
@dt_hayden: If you grab the "ground" to make your connection, you could potentially make a direct discharge at that point.

Good point

Max The Magnificent
User Rank
Blogger
Re: Notebook??
Max The Magnificent   8/13/2014 2:39:47 PM
NO RATINGS
@Antedeluvian: I hope I am not alone in noticing that a notebook can run on batteries, in which case you have no ground at all.

True, but I never use it that way -- I always have it plugged in when I'm working on a hobby project.

dt_hayden
User Rank
CEO
consumer versus industrial
dt_hayden   8/13/2014 2:37:02 PM
NO RATINGS
In general, grounding yourself through a piece of (consumer grade) electronic equipment for ESD control seems like a not so good idea.  You are making assumptions about the goodness of that ground and assuming the equipment can withstand discharges into that point.  If you are sure only the wriststrap connection touches the "ground" point, then currents are limited by the resistor in the strap anyway and less of a worry.  If you grab the "ground" to make your connection, you could potentially make a direct discharge at that point. 

Having said that, Tek scopes I have used in the past had a "grounded" banana jack on the front panel which I plugged into for ESD management.  My thinking was since it was industrial gear, Tek designs robust equipment, and the point was probably put there for that purpose, it was fine. 

If you are only dealing with isolated portable gear, I think it is more important to equalize potential to the gear, rather than to ground.  .I have clipped onto grounds of gear in these cases.  In this case, some (all?) soldering ground tips are grounded, so beware when soldering.

Max The Magnificent
User Rank
Blogger
Re: Maybe...
Max The Magnificent   8/13/2014 2:34:55 PM
NO RATINGS
@Crusty: I get over stretching the colied cable of the wristband by having a multiple socket strip...

Actually, that's not a bad idea -- I usually have a couple of these lying around -- but I'm going to check the USB thing first...

antedeluvian
User Rank
Blogger
Notebook??
antedeluvian   8/13/2014 2:34:46 PM
NO RATINGS
Max

I hope I am not alone in noticing that a notebook can run on batteries, in which case you have no ground at all.

Crusty1
User Rank
CEO
Re: Maybe...
Crusty1   8/13/2014 2:28:15 PM
NO RATINGS
Hi Max : I get over stretching the colied cable of the wristband by having a multiple socket strip, on a lead from the wall socket, in England these are very cheap from Ikea. The soldering Iron and powers supply go into two of the free sockests leaving me with two other sockets for wristband and antistatic mat.

This approach any use?

Max The Magnificent
User Rank
Blogger
Re: Maybe...
Max The Magnificent   8/13/2014 1:57:42 PM
NO RATINGS
@Duane: In most US wall sockets, the screw that holds the outlet plate on is grounded. If that's the case, you could just connect to that screw for your earth ground.

But they I still have the probem that the wall socket is quite a way from the table -- unless I attach a loong piece of wire -- and I don;t fancy attaching and detaching that wire each time I want to play with my electronics...

Max The Magnificent
User Rank
Blogger
Re: Maybe...
Max The Magnificent   8/13/2014 1:55:34 PM
NO RATINGS
@Duane: Just to be sure, I ran it past a couple of my ESD experts here [...] if it's less than 1 ohm, you're good to go.

Potential Happy Dance -- I'll check thsi as soon as I get home this evening an report back in the morning...

Duane Benson
User Rank
Blogger
Re: Maybe...
Duane Benson   8/13/2014 1:54:46 PM
NO RATINGS
In most US wall sockets, the screw that holds the outlet plate on is grounded. If that's the case, you could just connect to that screw for your earth ground.

<<   <   Page 9 / 10   >   >>


Most Recent Comments
Flash Poll
Top Comments of the Week
Like Us on Facebook
EE Times on Twitter
EE Times Twitter Feed

Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
EE Life
Frankenstein's Fix, Teardowns, Sideshows, Design Contests, Reader Content & More
Max Maxfield

Are Today's Designs Bound by the Constraints of Yesteryear?
Max Maxfield
26 comments
As part of my ongoing Pedagogical and Phantasmagorical Inamorata Prognostication Engine project (try saying that 10 times quickly), I'm working with Jason Dueck from Instrument Meter ...

Jolt Judges and Andrew Binstock

Jolt Awards: The Best Books
Jolt Judges and Andrew Binstock
1 Comment
As we do every year, Dr. Dobb's recognizes the best books of the last 12 months via the Jolt Awards -- our cycle of product awards given out every two months in each of six categories. No ...

Engineering Investigations

Air Conditioner Falls From Window, Still Works
Engineering Investigations
2 comments
It's autumn in New England. The leaves are turning to red, orange, and gold, my roses are in their second bloom, and it's time to remove the air conditioner from the window. On September ...

David Blaza

The Other Tesla
David Blaza
5 comments
I find myself going to Kickstarter and Indiegogo on a regular basis these days because they have become real innovation marketplaces. As far as I'm concerned, this is where a lot of cool ...