Breaking News
Comments
Newest First | Oldest First | Threaded View
<<   <   Page 8 / 10   >   >>
Max The Magnificent
User Rank
Author
Re: Maybe...
Max The Magnificent   8/14/2014 10:14:38 AM
NO RATINGS
@David: ...The best solution would be to get a mains cable with a proper 3-pin plug,  cut the...

This is what I was planning on doing (except using plugs that are designed for you to wire up yourself) until Wnderer suggested using the existing banana plugs on the wristbands/mats along with these $7 ground plug adapters.

Max The Magnificent
User Rank
Author
Re: power strip and ground plug adapter
Max The Magnificent   8/14/2014 10:11:52 AM
NO RATINGS
@Wnderer: Get a powerstrip and one of these $7 ground plug adapters.

This is obviously the way to go -- I'm going to order the adapters right now -- Max

Wnderer
User Rank
Author
Re: power strip and ground plug adapter
Wnderer   8/13/2014 7:46:03 PM
NO RATINGS
@David Ashton Great little gadget, much easier than my idea if you can get them easily.


Digikey has them.

 

 

David Ashton
User Rank
Author
Re: power strip and ground plug adapter
David Ashton   8/13/2014 6:17:14 PM
NO RATINGS
@Wnderer....sorry, only noticed this post after I posted mine above.  Great little gadget, much easier than my idea if you can get them easily.

David Ashton
User Rank
Author
Re: Maybe...
David Ashton   8/13/2014 6:14:31 PM
NO RATINGS
@Max...sorry to rain on your parade (or pee on your fire) but I would say 100% of all the brick type laptop and other power supplies I have ever taken apart (and there have been a few) have been switching types with the output isolated from the mains.

A mini-tower desktop computer might be different - those power supplies usually have a connection between the mains earth and the case of the PC....but I am not sure whether this will extend to the USB shield, I will check mine when I can.

Your solution might be to just switch your power supply off rather than unplugging it.  Of course you should also check if the power supply ground goes all the way through to the output.

The best solution would be to get a mains cable with a proper 3-pin plug,  cut the IEC end off (preferably while it is NOT plugged in :-), strip it back a bit, and cut off and insulate the white and black wires (which is what I think you have in the US) leaving the green earth wire only - and connect that to your anti-static mat.  This does assume you have a spare power outlet where you are working, and that G the G does not want to use said outlet while you are electronicking...

PS to avoid the white and black wires shorting, cut them off different lengths.  Then get some pliers and pull the insulation so you don't have wire ends sticking out.  Then insulate them with tape.   As the Irish would say....To be sure...to be sure...

Max The Magnificent
User Rank
Author
Re: Braided shield
Max The Magnificent   8/13/2014 5:41:37 PM
NO RATINGS
@MeasurementBlues: Congratulations Max, you've just created a pigtail, a wonderful source of radiated emissions.

Thank-you-very-much ... I'll be playing here all week :-)

MeasurementBlues
User Rank
Author
Google has found you
MeasurementBlues   8/13/2014 5:36:17 PM
NO RATINGS
@Max, I get a Google alert for "electrostatic discharge" and you've been picked up.

MeasurementBlues
User Rank
Author
Braided shield
MeasurementBlues   8/13/2014 5:30:59 PM
NO RATINGS
Congratulations Max, you've just created a pigtail, a wonderful source of radiated emissions.

I'll be posting an article to my EDN blog about how those pigtails are evil.

The braided shielding -- shown pulled back from the inner wires, twisted together, and sticking out of the right-hand side



MeasurementBlues
User Rank
Author
Re: Wear the wristband
MeasurementBlues   8/13/2014 5:26:26 PM
NO RATINGS
As you surely know, never ever float the scope.

zeeglen
User Rank
Author
Re: Wear the wristband
zeeglen   8/13/2014 5:24:09 PM
NO RATINGS
@Martin So if your circuit is floating and you're connected to the low side of its power supply, you should be OK.

Also a good idea to connect a scope probe ground to a floating circuit as the first connection so that the circuit is no longer floating.  I've zapped MOSFETs by connecting the probe tip to the gate first before the ground.

<<   <   Page 8 / 10   >   >>


Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...
See the Virtex® UltraScale+™ FPGA with 32.75G backplane ...
Vincent Ching, applications engineer at Avago Technologies, ...
The LT®6375 is a unity-gain difference amplifier which ...