Breaking News
Comments
Oldest First | Newest First | Threaded View
resistion
User Rank
Author
uneven spaces
resistion   8/15/2014 10:35:46 PM
NO RATINGS
This article must refer to LELE. With SADP, there's some relief but process must ensure adjacent spaces are (targeted to be) equal.

TanjB
User Rank
Author
know the rules
TanjB   8/17/2014 9:12:41 PM
NO RATINGS
Seems like if the foundry has control over the multi-patterning, and their choices impact the margins, then the only sane solution is for them to expose the rule deck.

Yes you can work around it but then you are adding slack to your design if you have uncertainty on what the actual pattern will be and so need margins in multiple places, only some of which will actually be needed.  As if things were not tight enough already...

Would this be an advantage for the few, like Samsung or Intel, with their own fabs (or others with privileged relations to a fab) and rules completely integrated into their tool sets?

jeremybirch
User Rank
Author
corners aren't everything
jeremybirch   8/18/2014 6:49:40 AM
NO RATINGS
Corners can be used to check that a design performs to speed under a variety of production and use variations whilst not exhibiting nasty side-effects - for instance steps that might speed up a design might also risk shoot-through on short paths. Statistical analysis can look a little deeper to look for bad scenarios that happen away from the extreme corners.

But the problem with multi-patterning is that the errors are highly correlated ie all copies of a given geometry might be shifted to the left and hence all of those nodes might have an increased capacitance whereas all copies of another node might have lowered capacitance (assuming all the cells coloured the same way). This may introduce a bad skew particularly if one node is a clock and the other a critical signal that it gates. Alternately every copy of a given cell might be coloured independently (if the EDA tool allows this) and hence some nodes will be faster and some slower. Corners don't really model this.


Worst of all is for two cells that are meant to be matched (eg analogue cells, sense amps etc) but in the colourings are the opposite of each other, this will mean that a mask offset will have opposite effects in the two cells and hence cause a big mismatch. Again just using corners will not spot this, and using monte carlo simulation will only spot a sensitivity to the possibility of this happening rather than the certainty caused by a colouring mismatch.

resistion
User Rank
Author
Re: corners aren't everything
resistion   8/18/2014 8:01:41 AM
NO RATINGS
Controlling both the overlay and the CD between exposures is extremely difficult. So SADP might be better to control, if you can correct for the sidewall distance after exposure.

Daniel Payne
User Rank
Author
Typo
Daniel Payne   9/6/2014 8:21:55 PM
NO RATINGS
In the second paragraph there's a typo, "cost-layout" should be instead "post-layout".



Datasheets.com Parts Search

185 million searchable parts
(please enter a part number or hit search to begin)
Radio
LATEST ARCHIVED BROADCAST

What are the engineering and design challenges in creating successful IoT devices? These devices are usually small, resource-constrained electronics designed to sense, collect, send, and/or interpret data. Some of the devices need to be smart enough to act upon data in real time, 24/7. Specifically the guests will discuss sensors, security, and lessons from IoT deployments.

Brought to you by:

Like Us on Facebook
Special Video Section
Once the base layer of a design has been taped out, making ...
In this short video we show an LED light demo to ...
The LTC2380-24 is a versatile 24-bit SAR ADC that combines ...
In this short video we show an LED light demo to ...
02:46
Wireless Power enables applications where it is difficult ...
07:41
LEDs are being used in current luxury model automotive ...
With design sizes expected to increase by 5X through 2020, ...
01:48
Linear Technology’s LT8330 and LT8331, two Low Quiescent ...
The quality and reliability of Mill-Max's two-piece ...
LED lighting is an important feature in today’s and future ...
05:27
The LT8602 has two high voltage buck regulators with an ...
05:18
Silego Technology’s highly versatile Mixed-signal GreenPAK ...
The quality and reliability of Mill-Max's two-piece ...
01:34
Why the multicopter? It has every thing in it. 58 of ...
Security is important in all parts of the IoT chain, ...
Infineon explains their philosophy and why the multicopter ...
The LTC4282 Hot SwapTM controller allows a board to be ...
This video highlights the Zynq® UltraScale+™ MPSoC, and sho...
Homeowners may soon be able to store the energy generated ...
The LTC®6363 is a low power, low noise, fully differential ...