After reading this series of articles on current sensing, you will have a solid grasp of the fundamentals of current sensing, devices used for current sensing, how to calculate the accuracy of a solution, and guidelines for printed circuit board (PCB) layout and troubleshooting. This article discusses the fundamentals of current sensing, including direct versus indirect sensing, input common-mode voltage, high versus low-side sensing, directionality, and output requirements.
Why is current sensing important?
Knowing the amount of current being delivered to a load can be useful in a wide variety of applications. For example, in low-power consumer products the supply current can be monitored to understand the system’s impact on battery life. The load current also can be used to make safety-critical decisions in over-current protection circuits. In motor control, knowing the magnitude and direction of the current can tell you the speed and direction of the motor. Finally, test fixtures can be developed that monitor all supply currents to gain an understanding of system subcomponent performance. Each of the aforementioned applications has different design requirements with respect to common-mode voltage, directionality, and accuracy.
Types of current sensing
There are two types of current sensing: direct and indirect. Indirect current sensing is based on Ampere’s and Faraday’s laws. By placing a coil (for instance Rogowski coil) around a current-carrying conductor, a voltage is induced across the coil that is proportional to the current. This allows for a non-invasive measurement where the sensing circuitry is not electrically connected to the monitored system. Since there is no direct connection between the sensing circuitry and the system, the system is inherently isolated. Indirect current sensing typically is used for load currents in the 100A-1000A range. This type of sensing, however, requires relatively expensive sensors and is not conducive to sensing currents on a PCB.
Direct current sensing is based on Ohm’s law. By placing a shunt resistor in series with the system load, a voltage is generated across the shunt resistor that is proportional to the system load current. The voltage across the shunt can be measured by differential amplifiers such as current shunt monitors (CSMs), operational amplifiers (op amps), difference amplifiers (DAs), or instrumentation amplifiers (IAs). This method is an invasive measurement of the current since the shunt resistor and sensing circuitry are electrically connected to the monitored system. Therefore, direct sensing typically is used when galvanic isolation is not required. The shunt resistor also dissipates power, which may not be desirable. Direct current sensing typically is implemented for load currents <100A. The remainder of this particular article series will focus on direct current sensing.
Input common-mode voltage
Input common-mode voltage is the most important specification when selecting a direct current sensing solution. It is defined as the average voltage present at the input terminals of the amplifier. Figure 1 depicts the definition of input common-mode voltage .
Figure 1: Definition of input common-mode voltage.
This specification is important because it limits our choice of differential amplifiers. For example, op amps and IAs require an input common-mode voltage within their power supplies. Difference amplifiers and CSMs, however, typically can accommodate input common-mode voltages in excess of their power supplies. This is useful in applications where the amplifier senses the shunt voltage in the presence of a large common-mode voltage and must interface with a low-voltage analog-to-digital converter (ADC). In such a scenario the amplifier and ADC can be powered with the same supply voltage regardless of the system’s common-mode voltage.
High-side versus low-side current sensing
When monitoring load current the designer can choose to place the sense resistor either between the supply voltage (Vbus) and load, or between the load and ground. The former is called high-side sensing whereas the latter is called low-side sensing.
Low-side sensing is desirable because the common-mode voltage is near ground, which allows for the use of single-supply, rail-to-rail input/output op amps. The drawbacks to low-side sensing are disturbances to the system load’s ground potential and the inability to detect load shorts. Figure 2 depicts a typical low-side sensing scenario.
Figure 2: Low-side current sensing.
High-side sensing is desirable in that it directly monitors the current delivered by the supply, which allows for the detection of load shorts. The challenge is that the amplifier’s input common-mode voltage range must include the load’s supply voltage, or Vbus. This requirement frequently necessitates the use of DAs or dedicated CSMs, which allow for common-mode voltages outside their voltage supply range. Figure 3 depicts a typical high-side sensing scenario.
Figure 3: High-side current sensing.
Depending on the application, the supply current may flow either in one direction (unidirectional) or both directions (bidirectional). Unidirectional designs are straightforward in that the output voltage of the amplifier does not need to distinguish direction. If a bidirectional design is required, however, how can the designer distinguish direction of current flow? Bidirectional solutions have an input for a reference, or pedestal voltage. The output of the device is then referenced to this known voltage. Output voltages above the known reference voltage are in one direction while output voltages below the known reference voltage are in the opposite direction. Figure 4 depicts the concept of current directionality.
Figure 4: Directionality.