# Selecting a solar energy conversion method

Individual cells are connected in series and parallel to form a panel. Panels are connected in series and parallel to form a photovoltaic array. Connecting cells in series increases the voltage. Connecting them in parallel increases the current. If an individual cell has a forward drop of 0.5V and with a given illumination produces 100mA, connecting 50 cells in series would produce a 25V string. Connecting 60 of the strings in parallel would produce a 25V, 6A panel. If each panel could deliver 150W, connecting 50 panels on a rooftop would deliver 7.5kW.

The four key parameters of a solar panel are:

Voc, the open circuit voltage where Iout = 0, Pout = 0

Isc, the short circuit current where Vout = 0, Pout = 0

Vmp, the output voltage at when the power extracted is maximum

Imp, the output current when the power extracted is maximum.

In ** Figure 6** the red curve is the current as a function of voltage and the green curve is the power as a function of voltage along with the location of the maximum power point.

**Figure 6****4. Transferring maximum power from a panel**

The objective is to find the maximum power point (MPP) and always operate the panel voltage and current at that point. The MPP will vary with irradiance and temperature. Decreasing irradiance is represented by a lower Isc. As Isc reduces, the MPP moves to a lower voltage. As temperature increases, Vmp reduces and the maximum power gets less. Voc, Isc, Vmp, Imp and the effects of temperature are shown in the panel manufacturer’s datasheets. A method is needed to dynamically track these changes as the panel environment changes and always operate the panel at the maximum power point, regardless of external factors.

Since the equivalent circuit of a solar panel is represented by a current source with parallel and series resistances, the Thevenin equivalent circuit can be shown as a voltage source with a single series resistance. To transfer maximum power from the voltage source to the load, the load resistance must equal the source resistance.

*shows the I-V curve and the load line R2 with the proper slope that intersects the I-V curve at the MPP.*

**Figure 7**

**Figure 7**This is easily accomplished with the STMicroelectronics SPV1020 boost converter with embedded maximum power point tracking (MPPT).

The SPV1020 DC-DC boost converter with embedded MPPT is an active power optimizer. Its purpose is to increase the output voltage from a panel while simultaneously adjusting the panel’s output voltage to Vmp. This optimizes or maximizes the power extracted from the panel. The converter’s output voltage is set by the user. The converter’s duty cycle is determined by the Perturb and Observe MPPT algorithm. The converter’s input voltage (or panel’s output voltage) is the dependent variable and is set by the formula:

**Vin = Vout * (1-duty cycle)**

In the SPV1020, the duty cycle starts out at a low value of 5 percent. The input voltage and input current are measured and power calculated. Then the duty cycle is increased. The new input voltage is measured and input power calculated. If the new power is greater than the old power the duty cycle is increased again. This process continues until the new power does not change or is less than the old power. If the new power does not change, that is the maximum power point. If the new power is less than the old power, the duty cycle DECREASES and the process is repeated, until the new power equals the old power, and the maximum power point has been determined. In this case the converter will be operating at the top of the power vs. voltage curve as shown in

*.*

**Figure 8**This Perturb and Observe algorithm runs continuously, at 256 times the switching period. The switching frequency is by default 100 kHz. The switching period is 10 microseconds and the MPPT algorithm is updated every 2.56 milliseconds.

**Figure 8**
Author

chrisrodgers 7/3/2012 8:06:22 PM

Author

dafi 7/4/2012 12:29:44 AM

Author

dave_dne 7/4/2012 1:16:40 AM

Author

sudhakar_amberroot 7/4/2012 3:54:23 AM

Author

chrisrodgers 7/4/2012 11:22:05 PM

Author

twarner250 7/5/2012 2:18:21 PM

Author

twarner250 7/5/2012 2:19:01 PM

Author

rroy22520 7/5/2012 3:08:01 PM

Author

jg_ 7/5/2012 10:30:41 PM

Author

Trinity51 7/6/2012 9:50:45 AM